Which L-theanine grade: source route, enantiomer and mesh
L-theanine has no salt, chelate or ester in the catalog: every grade is the same molecule, C7H14N2O3, CAS 3081-61-6. What changes between grades is the source route (tea-derived or fermentation), the enantiomer purity (L against D or DL), the assay envelope and the particle size. Those four lines decide the certificate, the label and, in the EU, the regulatory file, so the grade is a specification decision rather than a packing choice.
L-theanine has no salt to choose; the grade is the source route, the enantiomer purity, the assay envelope and the particle size.
Why there is no salt to choose
The label names the molecule, not a carrier. There is no theanine oxide, citrate or chelate to choose between, and no ratio between an active and a mineral to declare. The commercial product is the L-enantiomer, and every grade in the catalog is that same molecule at the same CAS number.
That removes one decision and puts weight on three. The source route decides whether the material is extracted from tea leaves or produced by fermentation or enzymatic synthesis; the molecule is identical, but the impurity fingerprint, the traceability record and the EU regulatory position are not. The enantiomer purity decides whether the powder is the L form or a mixture with the D form, which the rotation and chiral HPLC can show. The particle size decides how the powder flows, dusts and dissolves.
A grade is therefore a bundle of those three choices plus the assay envelope. Two suppliers can both sell “L-theanine 99%” and still be offering different documents, different trace profiles and different market files.
The catalog grade and the lines that move
| Line | Catalog grade | What to re-check on another grade |
|---|---|---|
| Source route | Tea-derived or fermentation | Is the route declared, and which carry-overs are limited? |
| Enantiomer | L-theanine | Is a D-theanine limit agreed, and is chiral HPLC reported? |
| Assay | 98.0–101.0% by HPLC | Is the basis stated, as-is or dried? |
| Specific rotation | +7.5° to +9.0° (c=2, water) | Are the concentration and solvent on the certificate? |
| Loss on drying | ≤0.5% | Is the limit wider, and does the pack control it? |
| Particle size | ≥95% through 80 mesh | Which cut, and was it measured on the lot? |
| Carry-over profile | Caffeine and polyphenols for tea; media and related amino acids for fermentation | Which screen appears on the certificate? |
| Regulatory file | Route-dependent in the EU | Does the file match the route and the destination? |
Read the table as a checklist for a material that is not the catalog grade, not as a second specification. A wider assay can suit a technical application and still fail a label that declares 98.0%; a tea-derived lot without a caffeine screen is not the same offer as a fermentation lot without a media screen. The use decides which grade is acceptable.
Mesh, flow and caking
The catalog form is an 80 mesh powder, meaning at least 95% passes a sieve with 80 openings per inch, roughly 180 µm. That is a fine powder: it dissolves quickly and disperses well in a stick pack, and it also dusts, carries static and cakes when it picks up moisture. The material is hygroscopic, so the sieve figure and the moisture limit belong together.
A granule is built from the same powder by agglomeration, so the chemistry does not change, but the flow, the dust and the wetting rate do. That makes it a new particle-size specification, not a packing variant. A press that struggles with the 80 mesh powder may run cleanly on the granule, which still has to meet the same assay, rotation and moisture limits.
Colour is a weak grade marker. White to off-white covers both the tea-derived and the fermentation material, and a slightly cream tone is not by itself a route indicator.
Matching the grade to the dosage form
A capsule or tablet takes the powder at its declared fill weight; the 80 mesh material flows well enough for many fills, and a granule is the answer when the press or the hopper needs it. The fill weight is fixed by the capsule size and the bulk density, so the declared dose and the particle form are linked decisions, not independent ones.
A stick pack or drink mix takes the fine powder because it dissolves readily; the solution is clear and slightly sweet, which is useful in a flavoured format. The same hygroscopicity that makes the powder dissolve quickly makes an open stick line a moisture risk, so the seal and the in-process hold belong in the specification.
One label distinction matters more than the mesh. A tea-derived L-theanine is an isolated ingredient, not the same as a green tea extract: the extract is standardised on tea polyphenols or caffeine, while the isolated material is standardised on theanine. If the label names a tea extract, an L-theanine certificate does not support that claim, and the reverse is also true. The comparison with GABA makes the same point about a second ingredient in the same category.
Specification lines for the grade
- “L-theanine, CAS 3081-61-6, C7H14N2O3, with the source route declared.”
- “Assay 98.0–101.0% by HPLC, with the basis stated.”
- “Specific rotation +7.5° to +9.0° (c=2, water); chiral HPLC L/D result where the enantiomer is part of the agreement.”
- “Loss on drying ≤0.5%; particle size ≥95% through 80 mesh.”
- “Heavy metals and microbiology as listed; a caffeine screen for a tea-derived lot.”
- “Destination market and source route checked against the regulatory file before the order.”
We supply the L-enantiomer; the source route is declared on the quotation and fixed in the specification. A change of route is a new specification and, in the EU, potentially a new regulatory file, so it should not be treated as a supply detail. The product hub carries the catalog specification; the COA page shows how the assay and rotation are reported; the compliance page covers the market file; the HPLC method note describes the separation; the quality page describes the release workflow.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation