02 Grade comparison

L-carnitine tartrate: the grade, the mesh and the fill

Technical document 02 · Reviewed 2026-11-20 · L-Carnitine Tartrate

On this page
  1. Why the tartrate is a grade of its own
  2. The carnitine forms side by side
  3. The powder: 80 mesh, flow and water
  4. What the grade does to the fill
  5. What to write into the specification
  6. When the tartrate is the wrong grade

L-carnitine tartrate is the 2:1 salt of L-carnitine and L-tartaric acid, and the grade decision starts with that ratio: 68.2% of the powder is carnitine and 31.8% is tartaric acid. The form is chosen against the base and the acetyl form, then against the mesh and the pack. This page covers the tartrate grade and what changes when a formula switches to it.

In one line

The tartrate grade is a 2:1 salt that carries 68.2% carnitine, so the decision is a trade between a 47% heavier fill and a powder that flows and holds less water than the base.

Why the tartrate is a grade of its own

The carnitine cation is the same in the base and in the tartrate; the counter-ion is what changes. In the tartrate, two carnitine cations are paired with one tartrate dianion, and the resulting crystal is less hygroscopic and freer flowing than the base. That is why a high-speed capsule line or a tablet press often starts with the tartrate rather than the base.

The grade is also a label decision. A panel that says L-carnitine base and a drum that contains the tartrate describe different ingredients, even when the carnitine figure per serving is the same. The salt name, the carnitine figure and the fill weight have to be settled together.

The carnitine forms side by side

Carnitine per gram, counter-ion and handling · three forms
PropertyL-carnitine baseL-carnitine L-tartrateAcetyl-L-carnitine HCl
CAS number541-15-136687-82-85080-50-2 (HCl)
Carnitine per gram1.00 g0.68 g0.79 g free base; 0.67 g as HCl
Counter-ionNone; zwitterionL-tartaric acid, 2:1None as the ester; hydrochloride common
Water uptakeHighModerateModerate to high
SolutionNear neutralAcidicAcidic
Label nameL-carnitineL-carnitine L-tartrateAcetyl-L-carnitine hydrochloride

The 0.68 figure is stoichiometry: two carnitine units at 161.20 g/mol plus one tartaric acid at 150.09 g/mol give 472.49 g/mol, of which 322.40 g is carnitine. The catalog range for carnitine content is 68.0–72.0%, so the lot certificate should be used for the label conversion rather than the theoretical figure alone.

The powder: 80 mesh, flow and water

The standard tartrate grade is a powder with ≥95% passing 80 mesh, and granulation is available where the line needs a coarser, freer-flowing material. The finer mesh suits a tablet blend or a stick pack that needs a uniform dispersion; the granulated grade suits a capsule line that is fighting dust or segregation. Particle size is a finishing specification, so it can change without a change in the chemistry.

The tartrate is less hygroscopic than the base, but it is not a dry-room exemption. Loss on drying is specified at ≤1.0%, and an opened pouch in a humid room will move that figure. The solution is clear and acidic, which matters for taste and for any acid-sensitive partner in the blend.

What the grade does to the fill

The conversion is fixed by the ratio. A formula that declares 500 mg of carnitine needs 500 ÷ 0.682 = 733 mg of tartrate; 1,000 mg of carnitine needs 1,466 mg. The base would need 500 mg and 1,000 mg respectively, so the tartrate fill is about 47% heavier for the same carnitine figure. That difference is large enough to change the capsule shell, the tablet weight or the number of servings per pack.

Use the lot's carnitine result for the final calculation, not the theoretical share. A lot at 69.5% carnitine needs 500 ÷ 0.695 = 719 mg for the same 500 mg declaration, while a lot at 68.5% needs 730 mg. The difference is small per capsule but adds up over a production run, and it belongs in the batch record rather than in a rule of thumb.

What to write into the specification

  • “L-carnitine L-tartrate, CAS 36687-82-8, C18H36N2O12, 2:1 salt.”
  • “Assay 98.0–102.0% by HPLC; state the basis.”
  • “L-Carnitine content 68.0–72.0% by HPLC or titration, with the method named.”
  • “Identification by HPLC retention and infrared spectrum; add chiral HPLC for the L configuration where the risk assessment needs it.”
  • “Loss on drying ≤1.0%; heavy metals and microbiology as listed.”
  • “Particle size ≥95% through 80 mesh; granulated on request.”
  • “Label name and carnitine basis confirmed before the first order.”

When the tartrate is the wrong grade

Three cases argue against it. If the label must say L-carnitine base, the tartrate is not a substitute, because the declared ingredient and the powder would differ. If the capsule or tablet cannot take a fill about 47% heavier, the base is the smaller option. If the formula is built around a neutral solution or an acid-sensitive partner, the tartrate's acidity is a liability rather than a convenience.

None of those is a defect in the grade. They are reasons to choose a different one, and the choice should be made before the label, the shell and the stability study are fixed. The direct comparison for a capsule is on the tartrate versus L-carnitine page; the release tests are on the COA page; the base specification is on the L-carnitine product page; the proof of the ratio is on the identity page; the water and pack question is on the stability page; the methods index covers the assays; and the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation