01 COA & batch testing

What the COA for L-arginine actually contains

Technical document 01 · Reviewed 2026-11-19 · L-Arginine

On this page
  1. The certificate as a test report
  2. What the titration measures, and what the rotation adds
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

An L-arginine certificate answers four questions at once: what the lot is, how much arginine it contains, which enantiomer was measured, and what else is in the drum. The certificate reports an acid–base titration on the dried basis, identification by IR and ninhydrin, specific rotation, loss on drying, residue on ignition, the pH of a 5% solution, particle size, heavy metals and microbiology. The figures below are the catalog specification; the batch certificate confirms the pouch or drum. A titration alone does not establish the L form, or that the material is the free base rather than the hydrochloride.

In one line

The assay reports how much arginine is in the drum; the rotation and the pH report which arginine it is.

The certificate as a test report

A useful certificate can be audited line by line. Each parameter needs the test, the method that produced the number, and the limit the lot was released against.

Identity, assay and moisture · L-arginine base
ParameterMethodRelease limit
AppearanceVisualWhite crystalline powder
IdentificationIR and ninhydrin reactionConforms to reference
AssayAcid–base titration, dried basis98.5–101.5%
Specific rotationPolarimetry, dried basis+26.3° to +27.7°
Loss on dryingGravimetric≤0.5%
Residue on ignitionGravimetric, ignited residue≤0.1%
pH (5% solution)Potentiometry10.5–12.0
Physical, contaminant and microbiological limits
ParameterMethodRelease limit
Particle sizeSieve analysis≥95% through 40 mesh
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

The pH line is not a formality. The free base carries a guanidino group that keeps a 5% solution strongly alkaline, and a formulator has to design around that. A pH at the bottom of the window can mean the powder has already taken up carbon dioxide from the air.

What the titration measures, and what the rotation adds

The release assay is an acid–base titration. The titrant, the endpoint technique — indicator or potentiometric — and the calculation belong on the certificate; without them the result cannot be reproduced. The figure is calculated against the dried weight, which is why loss on drying sits beside it. A value slightly above 100% inside the 98.5–101.5% window is method uncertainty, not extra arginine.

HPLC answers a different question. Arginine has no useful ultraviolet chromophore, so the method usually relies on derivatisation, ion-exchange separation with post-column ninhydrin, or mass detection. Here HPLC is the confirmatory and impurity method: it shows whether other amino acids travel with the lot and supports the identity IR begins. It does not replace the titration, and the certificate should say which technique produced which number.

The dried basis is a correction, not a measurement. Water leaves the calculation through the loss-on-drying result; carbon dioxide taken from the air is not water and is not corrected. That matters for a hygroscopic base: a lot that has absorbed moisture and carbon dioxide can pass the dried-basis assay while its as-is arginine content is lower and its pH sits below the specification.

Specific rotation is the chiral measurement. The L form rotates plane-polarised light clockwise, and the catalog window is +26.3° to +27.7° on the dried basis. Rotation depends on solvent, concentration, path length and temperature, so a certificate that omits those conditions cannot be compared with another. A value inside the window is consistent with the L form; a value near zero, or one that has moved across lots, is a finding that IR and titration will not explain.

Release limit versus batch result

The release limit is the gate; the batch result is what the laboratory found. They belong in separate columns, with the method beside each. A specification range printed in the result column proves only that the template was filled in.

Not every line tolerates a value near the edge. A rotation just above the floor is inside the window but leaves little room for method variation; a loss on drying close to 0.5% leaves little room for a humid filling room; a pH near the bottom of the window is worth a check for carbonate. None of those is automatically a rejection, but each is worth a question before the lot is accepted.

Residue on ignition catches a mineral diluent and some processing residues, but it does not catch the hydrochloride, because the chloride is lost on ignition. When the form is in doubt, ask for chloride. It is not on this catalog certificate, which is why the pH carries the form question and the rotation the chiral one; chloride belongs in the specification wherever the base is bought against a salt-sensitive formula.

What moves between batches

Loss on drying moves with the pack and the season: a pouch opened in a humid room gains water quickly, and a drum liner that is not reseated does the same. pH moves with carbon dioxide, so a lot exposed to air can drift downward while assay and rotation stay inside their windows.

Particle size moves with milling, colour with the drying step, and the assay with both moisture and carbonate load. The rotation should not move if the material is the L form. A slow drift across lots is more serious than one value at the edge, because it suggests a change in source, route or purification.

When to order an outside test

Use an outside laboratory for a new source, a first shipment into a regulated market, a form claim the supplier's certificate cannot support, or a disputed result. The useful panel is not a full repeat: polarimetry with conditions stated, chloride by ion chromatography or titration, an HPLC amino-acid profile, ICP-MS for the metals, loss on drying, and an IR spectrum against a reference.

Ask the laboratory to report its detection limit and sample preparation. A “not detected” entry means little without its detection limit; the figure describes the method, not the drum. Give the referee the retained sample, the certificate and the specification, and keep the lot code through both.

What to compare between suppliers

Put six lines side by side: the form as named; the assay with its method and basis; the specific rotation with its conditions; pH; loss on drying; and chloride. Two quotations that agree on the assay and diverge on the other five are not describing the same powder.

Then check traceability. The lot code should appear on the certificate, the pack and the retained sample, and the certificate should name the producer, not only the trader. Mesh and pack belong in the comparison too: a 40 mesh powder and a milled 80 mesh grade can share every chemical line and still behave differently on the line.

The catalog specification sits on the L-arginine product page. The form comparison is on the grades page; the tests that separate the base from the salt are on the identity page; the release workflow is on the quality page. The chromatographic method is described in the HPLC note, and the moisture test in the loss-on-drying entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation