L-arginine base or hydrochloride: choosing a grade
L-arginine is sold as the free base and as the monohydrochloride, and the two are different label ingredients. The base is strongly alkaline and carries the full mass as arginine; the salt is about 82.7% arginine, brings roughly 17% chloride with it, and gives a solution that is far less alkaline. The catalog form on this page is the base, a crystalline powder with at least 95% passing 40 mesh. The choice between the forms is set by the label, the dose and the matrix, not by which assay figure looks higher on a quotation.
The label ingredient and the dose decide the form; the assay percentage on the first quotation does not.
Why the form is a specification question
“L-arginine” on a purchase order is ambiguous. The base and the hydrochloride share the arginine entity but not the molecular weight, the counterion, the solution pH or the label name. A certificate for one does not describe the other, and a formulation weighed for one will be wrong if the other arrives.
The second axis is physical form. The catalog grade is a crystalline powder with at least 95% passing 40 mesh; an 80 mesh milled grade and a granulated grade are available on request. Mesh changes flow, dust and dissolution rate, not chemistry. Write both axes into the specification: the chemical form and the particle size.
Base and hydrochloride side by side
| Line | L-arginine base | L-arginine hydrochloride |
|---|---|---|
| Label name | L-arginine | L-arginine hydrochloride |
| CAS | 74-79-3 | 1119-34-2 |
| Formula and molecular weight | C6H14N4O2 · 174.20 | C6H14N4O2·HCl · 210.66 |
| Arginine per gram | 1.00 g | About 0.827 g |
| pH (5% solution) | 10.5–12.0 | Weakly acidic; the salt's own COA states the range |
| Moisture and carbon dioxide | Hygroscopic; absorbs CO2 from air | Hygroscopic; no alkaline surface for the same CO2 reaction |
| Assay basis | 98.5–101.5% by titration, dried basis, as the base | The salt's specification, calculated as the salt |
| What the label has to say | L-arginine, the free base | The hydrochloride, with the dose tied to the salt |
The table is not a ranking. Each form has a job, and the job is decided by the formula and by the label the brand intends to print.
pH, hygroscopy and the carbonate problem
The base is strongly alkaline because of its guanidino group, and the 10.5–12.0 window is part of the specification rather than an incidental measurement. In an acidic blend the base neutralises the acid, and if the blend is sealed — a stick pack or a sachet — the carbon dioxide released has nowhere to go. The result is swelling, pressure and a product that no longer matches its specification.
In air, the same chemistry runs slowly. The base takes carbon dioxide and water from the room and forms a carbonate on the surface; pH falls, mass rises, and the powder can cake. The hydrochloride does not present the same alkaline surface, but it is still hygroscopic and it brings a chloride load of about 17% by mass. Neither form is a free pass on packaging, and neither should be left in an open drum.
Both forms are freely soluble in water, so solubility seldom decides the choice. What decides it is the pH the formula can carry and the ingredient name the label has to show.
What the form does to the dose
The conversion is arithmetic. One gram of the hydrochloride delivers about 827 mg of arginine; to declare 1,000 mg of arginine from the salt, a formulator needs about 1,209 mg of the salt. The reverse is also true: a label that says 1,000 mg of L-arginine hydrochloride is declaring about 827 mg of arginine, not 1,000 mg.
That difference lands on the fill weight. A 500 mg fill of the salt carries about 413 mg of arginine, so the same fill of base and salt is not the same dose. A stick pack has more room, but the acid–base reaction matters more there, because the pack is sealed and the base can drive off carbon dioxide from any acidic component. In a tablet, the alkaline base can affect the pH of the granulation and the choice of excipients; in a chew or gummy, the water and heat of the process add their own questions.
The dose decision should be written before the purchase order, not after the first trial. Name the form, the arginine figure the label will declare, and the fill weight the machine can run.
What to write into the specification
- “L-arginine base, CAS 74-79-3, C6H14N4O2; not the hydrochloride.”
- “Assay 98.5–101.5% by titration on the dried basis; specific rotation +26.3° to +27.7° on the dried basis.”
- “Loss on drying ≤0.5%; residue on ignition ≤0.1%; pH (5% solution) 10.5–12.0.”
- “Particle size ≥95% through 40 mesh, or the agreed milled or granulated distribution.”
- “Chloride reported for each lot where the formula is salt-sensitive.”
- “Heavy metals and microbiology as on the catalog specification; lot code on the pack, the certificate and the retained sample.”
If the material is the hydrochloride, every line changes: the name, the CAS, the molecular weight, the assay basis, the pH range and the chloride line. A specification copied from the base and applied to the salt is not a specification; it is a template with the wrong noun.
When the other form is the wrong answer
Do not choose the base for an acidic, sealed powder if the formula has no room for the carbon dioxide it will release. Do not choose the hydrochloride when the label has to read “L-arginine” and the dose is expressed as arginine, unless the label is changed to match the salt. Do not switch forms to fix a flow problem: mesh and granulation are the tools for flow, and changing the salt to solve a hopper creates a labelling problem instead.
The catalog form is the base at 40 mesh. The product hub carries the specification; the COA page shows how each line is reported; the base-versus-hydrochloride page works through the dose and label arithmetic; the stability page covers the carbonate and packaging question; the compliance page covers the label name in each market.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation