Pure MK-7, 1% powder or oil: choosing a vitamin K2 grade
Vitamin K2 MK-7 is sold as an isolated menaquinone-7 concentrate, as a 1% spray-dried powder, or as an oil suspension. The three forms carry the same molecule at very different concentrations, so the grade decides the fill weight, the label declaration and the process. Choose on the dose and the dosage form, not on the largest percentage on the first quotation.
A 1% powder is not a weaker grade; it is a diluted one, and the dilution is what makes a 100 µg dose weighable.
Why the grade is a weighing decision first
A label dose of vitamin K2 is written in micrograms. A capsule fill, a tablet blend or a stick pack is weighed in milligrams. Pure menaquinone-7 at 100 µg is 0.1 mg, a mass that is difficult to weigh accurately on a production line and difficult to distribute evenly through a blend. A 1% powder turns the same 100 µg into 10 mg of powder, which is a normal weighing range and a normal blend component.
The grade therefore answers a physical question before it answers a commercial one: how much material has to move to carry the label dose, and can the line handle it uniformly? The concentration on the certificate is the result of that decision, not a ranking of quality.
Three forms, one molecule
| Form | MK-7 concentration | Matrix | Typical fit |
|---|---|---|---|
| Isolated MK-7 | 97–102% (EU synthetic spec) | None | Oil-filled capsules, concentrates, small-mass premixes |
| 1% spray-dried powder | 0.9–1.1% | Starch or gum arabic | Capsules, tablets, stick packs, dry blends |
| Oil suspension | Agreed and declared | Carrier oil | Softgels, oils, emulsified drinks |
The isolated grade is the reference point for the comparison; this catalog's standard grade is the 1% spray-dried powder. The EU entry's synthetic specification is 97–102% menaquinone-7, with at least 92% all-trans and no more than 6.0% cis isomers. A 1% powder carries the same molecule on a declared matrix; the all-trans ratio survives the dilution, but the content figure does not. An oil suspension is the same molecule dispersed in a fat, which suits a lipophilic fill and a softgel but adds an oil to the label and to the stability file.
What the carrier does
The carrier is not a neutral space filler. It gives the powder its flow, its dispersion and its dilution factor, and it appears in the ingredient list. Starch and gum arabic behave differently. A starch carrier usually gives a denser, less hygroscopic powder with good flow; a gum arabic matrix is designed to disperse in water and is the usual choice when the powder has to go into a drink mix or a stick pack. Both must be named on the certificate and on the label.
The physical specification supports the dosage form: at least 95% through 40 mesh for a powder that has to blend without lumps, loss on drying at or below 5.0% for a matrix that should not cake, and a declared carrier for the label. If the carrier changes, the flow, the dispersion, the fill weight and the label change with it, even when the MK-7 content stays inside 0.9–1.1%.
Converting a label dose into powder
The label dose is the mass of MK-7, not the mass of the powder. The conversion is arithmetic: divide the label dose by the MK-7 concentration of the grade. At exactly 1.0%, 100 µg of MK-7 sits in 10 mg of powder. At the bottom of the release range, 0.9%, the same dose needs 11.1 mg; at the top, 1.1%, it needs 9.1 mg.
| Label dose (µg MK-7) | Isolated MK-7 (mg) | 1% powder (mg) |
|---|---|---|
| 50 | 0.05 | 5 |
| 100 | 0.10 | 10 |
| 200 | 0.20 | 20 |
| 500 | 0.50 | 50 |
| 1,000 | 1.00 | 100 |
The table is the stoichiometric minimum, before overage and before the rest of the capsule fill. It also shows where a grade stops fitting. A 1% powder is comfortable for a 100 µg dose and still workable at 500 µg; at a multi-milligram dose the powder mass becomes the capsule, and the isolated or oil grade is the better physical match.
What the label can say about the grade
The label declares the vitamin K amount and the form, not the powder concentration. In the EU, the novel-food designation for this ingredient is "Menaquinone" or "Vitamin K2", and the ingredient list should name the form that is actually present. The carrier is declared in the same list. The vitamin K contribution is expressed against the EU nutrient reference value of 75 µg, so the percentage is calculated from the MK-7 mass, not from the powder mass.
In the US, the Supplement Facts panel declares vitamin K in micrograms and names the source in parentheses, for example "Vitamin K (as menaquinone-7)". A 1% powder does not become a 1% label claim; the panel still reports the micrograms of vitamin K that the serving delivers. The concentration belongs on the specification and the certificate, where a formulator can use it.
What to write into the specification
A grade specification should be short enough to audit and complete enough to order. For the standard grade: "Menaquinone-7 1% spray-dried powder; carrier starch or gum arabic, named on the certificate; MK-7 0.9–1.1% by HPLC; all-trans ≥92% of MK-7; loss on drying ≤5.0%; ≥95% through 40 mesh; no other menaquinone added." Add the source route, synthetic or fermentation, if the market file requires it.
For an isolated grade, replace the content range with the purity and isomer specification and keep the identification by retention time. For an oil suspension, add the carrier oil, the MK-7 concentration, the antioxidant if one is used, and the pack. The grade name on the purchase order should match the specification; "vitamin K2" alone does not say which of the three forms is being bought.
The catalog ranges are on the vitamin K2 MK-7 product page. The certificate lines are explained on the COA page; the light and heat limits are on the stability page; the ordering unit is on the MOQ page. The EU entry is summarised in the EU regulatory note, and the NRV is defined in the NRV glossary entry.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation