02 Grade comparison

Choosing a vitamin K2 MK-7 oil grade: carrier, concentration and form

Technical document 02 · Reviewed 2026-11-20 · Vitamin K2 MK-7 Oil

On this page
  1. Start with the microgram on the label
  2. One molecule, three matrices
  3. How the matrix behaves
  4. From micrograms to milligrams
  5. The clauses a purchase specification needs
  6. When the oil is the wrong input

Vitamin K2 MK-7 oil is sold here at one concentration, 1.0–1.1% in a carrier oil, so the grade conversation is not about picking a stronger or weaker oil. It is about choosing a matrix: an oil for a lipid fill, a 1% spray-dried powder for a dry dosage form, or an isolated concentrate when the dose is large and the fill is small. The carrier and the production line decide, and the label follows.

In one line

The 1% concentration makes the dose weighable; the carrier and the dosage form decide whether the oil or the powder is the right grade.

Start with the microgram on the label

Start with the size of the dose on the label. A daily MK-7 claim is written in micrograms; a capsule fill, a tablet blend or the fill of a softgel is handled in milligrams. A 100 µg claim is 0.1 mg of pure menaquinone-7, a quantity that is awkward to weigh and awkward to spread evenly through a batch. Diluting the molecule to 1% turns that claim into roughly 10 mg of a material the line can actually handle.

That dilution is the reason the 1% forms exist. It is not a comment on potency. The oil and the powder reach almost the same concentration, so the choice between them is about how the material behaves in the process and what the label has to declare.

One molecule, three matrices

The three MK-7 forms side by side
FormMK-7 concentrationMatrixMass for 100 µgTypical fit
MK-7 oil (this product)1.0–1.1%Carrier oil, named on the specification9.1–10 mgSoftgels, oil blends, lipid fills
Spray-dried powder, 1%0.9–1.1% MK-7Starch or gum arabic matrix9.1–11.1 mgCapsules, tablets, stick packs, dry blends
Isolated MK-797–102% (EU synthetic spec)NoneAbout 0.1 mgOil-filled capsules, concentrates, premixes

The isolated grade is a reference point rather than a drop-in: at 97–102% it is the pure material described in the EU synthetic-route specification, and a 100 µg dose is 0.1 mg. The two 1% forms put the same molecule on different matrices. The oil is a liquid solution in a carrier oil; the powder is a solid dispersion on starch or gum arabic. The table keeps the concentration, the matrix and the dose mass in one view.

How the matrix behaves

An oil has no particle size and no flow to specify. It is a clear yellow to amber liquid that does not dissolve in water but mixes with fats and organic solvents. Those properties are the reason it belongs in a softgel or an oil blend and the reason it does not belong in a dry mix or a drink powder that has to disperse. The carrier oil is part of the specification and appears in the ingredient list; change the carrier and the allergen statement, the mouthfeel and the stability work all change.

The powder brings the opposite set of properties: a solid that flows, blends and, with gum arabic, disperses in water. It carries a loss-on-drying limit and a particle-size limit. The oil's own release check is the peroxide value, which reports on the carrier's condition rather than on the MK-7 content.

From micrograms to milligrams

The label dose is MK-7, so the oil mass is the dose divided by the concentration. At 1.0%, 100 µg needs 10 mg; at 1.1%, 9.1 mg. The table also shows the powder's edges so a formulator can see how little the mass actually differs between the two 1% forms.

MK-7 dose converted to oil and to 1% powder
Label dose (µg MK-7)Oil at 1.0% (mg)Oil at 1.1% (mg)Powder at 0.9% (mg)Powder at 1.1% (mg)
505.04.55.64.5
10010.09.111.19.1
20020.018.222.218.2
50050.045.555.645.5
1,000100.090.9111.190.9

These are minimum masses at release, before overage and before the remainder of the fill. A softgel fill is much larger than 10 mg; the oil is a concentrate that is diluted into it. A capsule built on the powder uses 10–11 mg as one component of a larger fill and carries the powder's carrier into the capsule as well.

The clauses a purchase specification needs

  • “Menaquinone-7 1% oil, CAS 2124-57-4, C46H64O2; carrier oil named.”
  • “MK-7 1.0–1.1% by HPLC, as-is on the oil; identity by HPLC retention and UV spectrum.”
  • “All-trans and cis reported separately; the all-trans limit is written into the purchase specification.”
  • “Peroxide value ≤10.0 meq O₂/kg; antioxidant declared if used.”
  • “Heavy metals and microbiology as listed; 1 kg or 5 kg amber bottle.”
  • “Storage sealed, upright, dark and cool; destination market confirmed before the order.”

When the oil is the wrong input

Tablets, hard capsules, stick packs and dry blends are powder territory. A liquid oil adds a step to a dry process and cannot be made water-dispersible without an emulsion, so the 1% powder is the practical input. At the other end, a large dose in a small fill is a job for the isolated concentrate: at 1%, the oil would be mostly carrier.

The oil wins when the fill is already a lipid: a softgel, an oil blend, a lipid-based delivery system. The powder wins when the fill is dry. A change in either direction is a new specification and a new label, not a mathematical conversion. The oil-versus-powder comparison takes the carrier, overage and label questions further. The catalog oil is on the product page; the powder is on the MK-7 powder page; the COA page sets out the certificate lines; the stability questions are on the stability page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation