06 Identity & adulteration

How we prove a vitamin B5 lot is calcium D-pantothenate

Technical document 06 · Reviewed 2026-11-19 · Vitamin B5

On this page
  1. The identity layers
  2. The calcium ratio: proving the salt
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A calcium D-pantothenate lot is identified by measurements that have to agree: IR and HPLC against the reference, a specific rotation inside +25.0° to +28.5°, a calcium figure of 8.0–8.6%, and an assay of 98.0–101.0% on the dried basis. The rotation separates the D form from the racemic DL material, and the calcium separates the salt from the free acid or panthenol. The assay alone cannot do either job.

In one line

The IR and HPLC name the molecule, the rotation shows the D form and the calcium figure shows the salt; a lot needs all three to agree.

The identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Layers of calcium D-pantothenate identity
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, formulaPaperwork only
IR and HPLCIs the molecule pantothenate?IR spectrum and HPLC retentionThe molecule, not the form
Specific rotationIs it the D form?Polarimetry on the dried basisThe configuration
CalciumIs it the calcium salt?Complexometric titration or ICP-OESThe counter-ion
Mass balanceIs it diluted?Assay, loss on drying, impuritiesConsistency of the numbers

The layers are not alternatives. IR and HPLC can match the reference while the rotation falls outside the window, which points to the DL or L form. The rotation can be right while the calcium is low, which points to the free acid, the sodium salt or a dilution. The calcium can be right while the assay is low, which points to a calcium-rich diluent.

The calcium ratio: proving the salt

The salt carries one calcium ion for every two pantothenate anions. At 100% assay, the theoretical calcium content is 40.08 ÷ 476.53 = 8.41% by mass. A calcium result close to that figure, with an assay inside 98.0–101.0%, is consistent with calcium pantothenate. A low calcium figure points to sodium pantothenate, the free acid or a dilution; a high figure points to a calcium-rich diluent or a different calcium salt.

The ratio is the check. Divide calcium by assay on the same basis: a pure salt sits near 0.084. A powder blended from calcium pantothenate and a calcium salt can land inside both windows while the ratio is wrong; so can a blend with sodium pantothenate. The certificate should report calcium and assay on the same basis, and the reader should do the division.

Calcium by complexometric titration is the catalog method; ICP-OES is the independent check and also reports sodium, which is useful when a sodium salt is suspected.

X-ray diffraction: the solid-state check

X-ray diffraction answers a different question: is the solid crystalline, and does its pattern match a reference? Calcium pantothenate is a crystalline salt, so a diffraction pattern can show whether the solid is crystalline and whether the pattern matches a reference. It is not a purity assay, it does not measure the counter-ion, and it does not prove that an amorphous carrier is absent.

Ask for the reference pattern and the detection limit before reading a “match” statement. XRD is not a routine release test for this product, and a certificate that reports “XRD conforms” without the pattern has added little. The method is most useful when the question is solid form or when a new source has to be compared with an existing one.

What adulteration looks like

Calcium pantothenate substitutions and the signals
AdulterantWhat it isSignalTest
DL-calcium pantothenateRacemic salt, not the D formRotation near zero or negativePolarimetry, chiral HPLC
Free pantothenic acidNo calcium; viscous materialCalcium absent; form differsCalcium, IR, HPLC
PanthenolAlcohol, not the saltNo calcium; different IR and retentionIR, HPLC, calcium
Lactose or maltodextrinCarrier or diluentAssay low; LOD and IR differMass balance, IR
Calcium salt diluentRaises calcium without assayCalcium/assay ratio highCalcium, mass balance
Sodium pantothenateDifferent counter-ionCalcium low; sodium highCalcium, sodium by ICP-OES

Colour is the weakest signal: white to off-white covers a wide range, and a blend can match it. The stronger signals are the rotation, the calcium figure and the mass balance. A certificate that reports appearance and assay but not rotation or calcium has left the most likely substitution untested.

How to write identity into the specification

  • “Calcium D-pantothenate, CAS 137-08-6, C18H32CaN2O10.”
  • “Assay 98.0–101.0% on the dried basis by HPLC; loss on drying ≤5.0%.”
  • “Identification by IR and HPLC against the reference.”
  • “Specific rotation +25.0° to +28.5° on the dried basis.”
  • “Calcium 8.0–8.6% by complexometric titration; report the basis.”
  • “No DL form or free acid above the agreed limit; state the limit in writing.”
  • “Particle size ≥95% through 40 mesh; heavy metals and microbiology as listed.”

The specification should also name the pack and the retest period, because identity is checked on the retained sample as well as on the release sample. The product hub carries the catalog values; the COA page shows where each result sits on the certificate.

Five questions for the supplier

  1. Which form is this lot, and which CAS number is on the certificate?
  2. Can you provide the IR spectrum and the HPLC chromatogram, not only the assay percentage?
  3. What are the specific rotation and the calcium result for this lot, and on which basis?
  4. What is the loss on drying, and how was the dried-basis assay calculated?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single assay percentage does not. The grades page compares the forms; the level-four comparison covers the salt and the label; the methods library explains the separation; the quality page describes the retained sample and the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation