Thiamine mononitrate grades: powder, flow and the salt decision
Thiamine mononitrate is supplied as a standard 80 mesh powder, with a granulated form on request. The grade decision that changes the most is the salt itself: the mononitrate and the hydrochloride differ in water uptake, solution pH and label name, and the vitamin content per gram differs by about three percent. Within the mononitrate, particle size and flow decide which dosage form the powder suits, not the assay percentage.
The grade is a particle and salt decision: the vitamin is the same, but the flow, the water uptake and the name on the label are not.
Why the mononitrate has few grades
Thiamine mononitrate is a synthetic vitamin made at a defined purity, so the range is narrow: one chemistry, a small number of physical forms. The differences that matter to a buyer are how the powder flows, how much dust it makes, how fast it dissolves, and how much water it takes up in a hopper. Those are finishing decisions, not a second grade of the molecule.
The larger choice is the salt. The monograph of the hydrochloride allows up to 5.0% water and the salt is hygroscopic; the mononitrate allows 1.0% loss on drying and is the lower-hygroscopicity form. That is why a dry blend, a tablet or a fortified flour usually specifies the mononitrate, while an acidic beverage usually specifies the hydrochloride. The level-four comparison takes that decision apart.
The forms side by side
| Form | Particle | Flow and dust | Fits |
|---|---|---|---|
| Standard powder | ≥95% through 80 mesh | Free-flowing; some dust in handling | Capsules, tablets, dry blends, stick packs |
| Granulated, on request | Coarser agglomerates | Better flow, less dust, slower to dissolve | Premixes, tablet compression, drum handling |
| Thiamine hydrochloride | Its own specification | Hygroscopic; dissolves readily | Acidic liquids, syrups, clear beverages |
Granulation is a specification change, not a packing choice. It moves the particle-size line, the bulk density, the flow and the dissolution time, and it should be written into the specification before the order. A granulated lot and a standard powder are not interchangeable in a validated tablet process even when the assay is identical.
Flow, dust and the blend
The standard powder is fine enough to disperse quickly but light enough to dust. In a low-dose premix, dust is a loss and a hygiene issue: material sticks to the mixer wall, and the assay of the finished blend depends on how much stayed in the air. A granulated grade reduces the dust and improves flow, at the cost of a slower dissolve and a coarser mouthfeel in a stick pack.
Segregation is the other physical risk. A fine vitamin blended with a coarse carrier can separate in a drum or during conveying, so the samples taken from the top and the bottom of a batch may not agree. Granulation narrows the particle-size gap between the vitamin and the carrier, which is one reason a premix supplier asks for it. Ask for the particle-size distribution, not only the “≥95% through 80 mesh” line, when the blend is sensitive.
For tablets, flow and compressibility decide the fill weight. For capsules, bulk density decides how much powder fits in a size. Neither property is on the certificate, so a trial on the real equipment is worth more than a second assay.
Dose arithmetic and the label
The label and the weigh-up have to use the same basis. Thiamine mononitrate is 81.1% thiamine by mass, so 1 mg of declared thiamine needs 1.23 mg of the salt, and 100 mg of the salt delivers 81.1 mg of thiamine. The hydrochloride is 78.7% thiamine, so the same 1 mg of thiamine needs 1.27 mg of that salt. Switching salt changes the weight behind the claim by about three percent.
That difference is small but real, and it compounds at high doses. A 500 mg thiamine claim needs 617 mg of the mononitrate or 635 mg of the hydrochloride, which matters when the capsule size is already fixed. The assay range is a second, separate correction: a lot at the low end of the range contributes less thiamine per gram than one at the top, and an overage has to be calculated on the measured result.
The dosage form follows the same logic. A tablet or capsule takes the mononitrate for its low water uptake. A stick pack blended dry takes either salt, but the mononitrate is more forgiving in the filling room. A clear acidic drink takes the hydrochloride, because the mononitrate dissolves more slowly and leaves the solution near neutral.
What to write into the specification
- “Thiamine mononitrate, CAS 532-43-4, C12H17N5O4S.”
- “Assay 98.0–101.0% by HPLC; the certificate states the basis.”
- “Identification by HPLC retention and infrared spectrum.”
- “Loss on drying ≤1.0%; pH 6.5–7.5 in 5% solution.”
- “Particle size ≥95% through 80 mesh; granulated form on request only.”
- “Heavy metals and microbiology as listed; pack and lot code stated.”
Add the destination market and the intended dosage form. A specification that names the salt, the assay basis and the particle profile can be quoted and tested; one that says “vitamin B1 powder” cannot.
When the mononitrate is the wrong choice
If the formula is an acidic clear beverage, a syrup or a liquid concentrate, the hydrochloride is the easier starting point: it dissolves readily and brings an acid pH that suits thiamine. The mononitrate can be used in a liquid if the pH is adjusted and the hold time is validated, but it is not the default. If the process uses a sulfiting agent, neither salt is a good carrier, because sulfite cleaves the molecule.
If the label already names the hydrochloride and the stability file was built around it, a switch to the mononitrate is a new specification, a new dose calculation and a new stability question. The reverse is equally true. The salt is part of the identity of the product, not a purchasing convenience.
The product hub lists the catalog specification and the packs. The mononitrate versus hydrochloride page covers the water and label consequences; the COA page shows how the grade is released; the stability page covers the matrix; the hydrochloride product page is the other salt; the methods library explains the particle-size and assay tests, and the quality page covers release.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation