01 COA & batch testing

What the COA for retinyl palmitate actually contains

Technical document 01 · Reviewed 2026-11-20 · Retinyl Palmitate

On this page
  1. The certificate as a test report
  2. The IU figure and its basis
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

A retinyl palmitate certificate reports appearance, HPLC identification with a UV spectrum, the assay in MIU/g, the retinol equivalent, the carrier, loss on drying, particle size, the heavy-metal panel and microbiology. Each line needs its method and release limit, and the measured result belongs in its own column. The limits below are the catalog specification; the batch COA confirms a particular pouch or drum.

In one line

The IU/g result is an HPLC figure on a carrier, so the certificate has to name the method, the conversion and the matrix beside it.

The certificate as a test report

A certificate is auditable when each row answers three questions: what was measured, which method produced the number, and which limit the lot was released against. For this product there is a fourth question, because the vitamin is dispersed in a carrier and the carrier is most of the powder. A row that says only “conforms” asks the reader to accept a conclusion without the evidence behind it.

Identity, assay and matrix · retinyl palmitate 1.0 MIU/g powder
ParameterMethodRelease limit
AppearanceVisualLight yellow to yellow powder
IdentificationHPLC retention and UV spectrumConforms to a retinyl palmitate reference
AssayHPLC with UV detection1.0–1.1 MIU/g
Retinol equivalentCalculated from the assay300,000–330,000 µg RE/g
CarrierDeclarationNamed on the certificate
Loss on dryingGravimetric≤5.0%
Particle sizeSieve analysis≥95% through 80 mesh

The lot code, dates, pack size and specification version belong on the same sheet. A result column filled with the specification range is a copy of the gate, not a measurement. “Passes specification” is still a conclusion; the reader should be able to reach it from the numbers above.

The IU figure and its basis

The IU is not a mass unit; it counts vitamin A activity. The convention assigns 3.33 IU to one microgram of retinol, so one IU equals 0.3 µg of retinol equivalent. A 1.0 MIU/g powder therefore contains 300 mg of retinol equivalent per gram. Pure retinyl palmitate is about 1.82 MIU/g, because retinol is 54.6% of the ester by mass. At 1.0 MIU/g the powder is roughly 55% ester; at the top of the catalog range, 1.1 MIU/g, it is roughly 60%.

That arithmetic is why the carrier line matters. The rest of the powder is carrier, moisture and minor solids, and its identity and ratio are part of the specification. The certificate should state whether the assay is reported as sold or on the dried basis. With loss on drying allowed up to 5.0%, a dried-basis figure reads above an as-sold figure, and the two are not interchangeable.

The method also needs a basis. A direct HPLC method reports the ester; a method that saponifies the sample reports total vitamin A after hydrolysis, including any free retinol. Both are legitimate, but two results are comparable only when the method and the basis match. A figure without either is a number, not a specification result.

Release limit versus batch result

The gate and the measurement are different things. The release limit is the boundary the lot must meet; the batch result is what the laboratory found on that lot. Keep them in separate columns, with the method beside them. The table below shows what the result column should contain for each line.

What the result column should contain
ParameterRelease limitResult column
Assay1.0–1.1 MIU/gA measured MIU/g with the basis and the method
Retinol equivalent300,000–330,000 µg RE/gThe calculated figure with the conversion shown
Loss on drying≤5.0%A measured percentage
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 80 meshThe measured percentage through the sieve

The carrier is declared, not assayed. The certificate should name it, and the buyer should ask for the ratio and the source where they affect the label. The catalog does not set a free-retinol or cis-isomer limit. When oxidation is a concern, ask for the chromatogram and the stability summary rather than reading the IU figure as the whole picture.

What moves between batches

A heavier vitamin load in the emulsion raises the IU/g; dryer losses lower it. The carrier ratio changes the rest of the powder, and a carrier lot with a different moisture content shifts the as-sold figure without any change in the vitamin input. Milling and sieving set the 80 mesh result, so a changed screen shows up there first.

Colour is the least quantitative line and often the most revealing. Light yellow to yellow is a wide window, and a shift inside it is not an identity failure. A markedly deeper or duller powder can point to heat exposure, a different carotenoid load or an oxidation product while the assay still passes. The isomer profile is a finer signal: HPLC can show a growing cis region beside the all-trans peak, and that change may not move the IU/g below its limit until late.

If an antioxidant is present, its identity and level can change between lots, and the certificate or the specification should say so. A trend across several lots says more than one result near an edge. The lot code should match the certificate, the pouch or drum, and the retained sample.

When to order an outside test

Order an independent test for a new source, a first shipment into a regulated market, a label that names the ester, or a disputed result. The useful panel is HPLC with UV against a retinyl palmitate standard, saponification followed by gas chromatography of the fatty acid to show palmitate, loss on drying, ICP-MS for the metal panel, microbiology and a screen for beta-carotene.

Ask the laboratory for its detection limit on each screen. A “not detected” line without a limit is evidence about the method's sensitivity, not about the sample. The report should name the column, mobile phase, wavelength and assay basis, and state whether the sample was saponified.

Chain of custody matters: the sample tested should be the sample retained, and the report should identify the lot. If a result is contested, give the referee the retained sample, the certificate and the specification, and ask for the tests that separate the esters.

What to compare between suppliers

Put eight lines side by side: ester and CAS number; assay in MIU/g and its basis; method and reference standard; retinol equivalent; carrier, ratio and source; loss on drying; particle size; and the contaminant and microbiology panels. Two quotations that agree on IU/g but differ on ester, carrier or basis are not describing the same powder.

Traceability is the second check. The certificate should identify the manufacturer and the carrier, and one lot code should appear on the certificate, the pack and the retained sample. The specification version belongs on the sheet as well.

The catalog table is on the retinyl palmitate product page. The ester comparison sits on the vitamin A page, the separation is described in the analytical methods library, and the release workflow is on the quality page. The tests that separate the esters are on the identity page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation