02 Grade comparison

Potency, carrier and mesh: choosing a retinyl palmitate grade

Technical document 02 · Reviewed 2026-11-20 · Retinyl Palmitate

On this page
  1. Why the grade is a separate decision
  2. The range at its two ends
  3. Powder, granule and the carrier
  4. Matching the grade to the dosage form
  5. What to write into the specification
  6. When a different grade is the wrong choice

Retinyl palmitate is catalogued as a 1.0–1.1 MIU/g powder on a carrier, sieved to 80 mesh, with a granulated form available on request. Within that range the grade choice is IU density, carrier system and particle form. All three remain retinyl palmitate; an acetate or the free retinol is a different product with a different label name.

In one line

The grade is the IU density, the carrier and the particle form; the ester name is the identity, not the grade.

Why the grade is a separate decision

Two powders can both read “retinyl palmitate 1.0 MIU/g” and still differ in the mass of ester they carry, the carrier that surrounds it, and the way they flow. The IU figure fixes the vitamin activity per gram, not the powder's density, its allergen profile or its behaviour in a tablet press. Those belong to the grade.

The carrier is the largest single component after the ester. At 1.0 MIU/g the ester is about 55% of the powder; the rest is carrier, moisture and minor solids. A different carrier ratio changes the label, the mouthfeel of a stick pack and the way the powder picks up water. The particle form changes flow, dust and segregation. A grade is therefore a package of four decisions: ester, IU density, carrier and mesh.

The range at its two ends

The catalog range is narrow by design: 1.0 to 1.1 MIU/g, a ten percent spread. The lower end leaves more carrier and a slightly larger powder mass per IU; the upper end carries more ester and less carrier. The granulated option keeps the same chemistry and changes the physical form for handling.

Retinyl palmitate grades in the catalog range
GradeRetinol equivalentEster massTypical use
1.0 MIU/g powder, 80 mesh300 mg RE/gAbout 55%Standard capsule, tablet and stick-pack blend
1.1 MIU/g powder, 80 mesh330 mg RE/gAbout 60%Lower powder mass per IU; tighter fill weight
Granulated 1.0–1.1 MIU/g300–330 mg RE/gAbout 55–60%Flow and dust control on request

The ten percent difference is small in a formula but not always negligible. A capsule that needs 3,000 IU takes 3.00 mg of the 1.0 MIU/g powder and 2.73 mg of the 1.1 MIU/g powder before any overage. On a fill weight of a few hundred milligrams, that is a rounding change; on a low-dose tablet it may decide whether the vitamin fits.

Powder, granule and the carrier

The standard form is an 80 mesh powder: at least 95% passes the sieve. A fine powder disperses quickly in a drink mix and blends evenly in a dry premix, but it also makes dust and can segregate from coarser excipients. Granulation binds the particles into a coarser, freer-flowing form; it reduces dust and improves flow, though dispersion is slower and the bulk density changes.

The carrier can be gelatin, starch, sucrose, a gum or a blend. The certificate must name it, and the buyer should ask for the ratio and the source where they affect the label. Gelatin brings an allergen question and a dietary one; sucrose is a sugar for labelling; starch can raise a gluten question. These are grade facts, not marketing details, and they should be settled before the first stability batch.

Colour is a weak grade signal. Light yellow to yellow covers the range, and a slightly deeper powder is not automatically a different ester. The stronger checks are the IU/g, the carrier declaration and the mass balance between them.

Matching the grade to the dosage form

For a capsule or tablet, the 80 mesh powder is the usual starting point: it blends, it fills and it can be compressed with the rest of the formula. The 1.1 MIU/g end helps when the vitamin must occupy less space. A granulated grade is worth testing when the blend is dusty, when flow in the hopper is inconsistent, or when the vitamin segregates from a coarse excipient.

For a powder stick or a drink mix, dispersion matters more than flow. The fine powder wets and disperses in warm water, though the ester is fat-soluble and the drink will be an emulsion or a suspension rather than a clear solution. The carrier can affect taste, mouthfeel and the label. If the product claims no added sugar, a sucrose carrier matters; if it makes a vegan claim, a gelatin carrier matters.

Dose arithmetic is shared across the range. A 3,000 IU portion needs 3.00 mg of the 1.0 MIU/g powder, or 2.73 mg at 1.1 MIU/g, before overage. An 800 µg RE portion needs 2.67 mg of the 1.0 MIU/g powder. Those figures are arithmetic, not a recommended intake, and they belong next to the label conversion rather than in a separate note.

What to write into the specification

A usable grade line has seven parts. It names the ester and the CAS number, states the IU/g and the HPLC method, gives the retinol equivalent, names the carrier and its source, fixes the loss on drying and the mesh, and adds the contaminant and microbiology panels. If an antioxidant is present, it belongs in the line too, with its identity and level.

  • Name retinyl palmitate, with CAS 79-81-2 and the formula.
  • State the IU/g, the HPLC method and whether the result is as sold or dried.
  • Give the retinol equivalent in µg RE/g.
  • Name the carrier, its source and ratio; declare any antioxidant.
  • Fix loss on drying at ≤5.0% and the 80 mesh particle size.
  • Attach the heavy-metal and microbiology panels.
  • Record the destination market, label name and overage policy on the order.

The grade line is also a change-control line. A switch from 1.0 to 1.1 MIU/g, from powder to granule, or from one carrier to another is a new specification, a new certificate and often a new label. The old stability file does not carry over, because the powder mass, the carrier load and possibly the allergen statement have changed.

When a different grade is the wrong choice

Do not move to the upper end of the range to make a tablet smaller if the label claim and the overage have not been recalculated. Do not switch to a granulated grade to solve a flow problem without checking dispersion in the finished drink; a granule that flows well can sit at the bottom of a stick pack. Do not accept a carrier change on the certificate alone: the label, the allergen statement and the taste have to be reviewed.

If the formula needs an IU density outside the 1.0–1.1 MIU/g range, or if the label and the market file already name retinyl acetate, the palmitate range is not the answer. The ester is the identity, and the grade cannot substitute for it. The retinyl palmitate product page carries the catalog table; the vitamin A page covers the acetate range; the analytical methods library describes the HPLC assay; the quality page covers release. The palmitate versus acetate page takes the ester comparison further.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation