06 Identity & adulteration

How we prove a niacin lot is nicotinic acid

Technical document 06 · Reviewed 2026-11-19 · Niacin

On this page
  1. Four layers, four different questions
  2. One mole of base per mole of acid
  3. X-ray diffraction and the solid form
  4. The substitutions that turn up
  5. Writing the specification so the proof is possible
  6. Five questions for a supplier

Four checks carry the proof: identification by IR and UV against a reference, a melting range inside 234–238 °C, an assay by titration on the dried basis inside 99.0–101.0%, and the chloride and sulfate limit tests, which a blended or substituted lot tends to fail first. One assay figure proves that acid groups are present in the expected proportion; it does not prove that they sit on a pyridine ring in the 3-position. The certificate has to carry the identity lines, and the specification has to say what the laboratory compared against.

In one line

The assay counts acid groups; the IR, the melting range and the two limit tests say those groups belong to nicotinic acid.

Four layers, four different questions

Identity is not one test. Each layer answers a question the others cannot, and a supplier who offers only an assay has answered the narrowest one.

Identity layers · what each test proves and what it cannot
LayerTestWhat it proves
SpectralIR and UV against a referenceThe functional groups and the substitution pattern of the ring
ThermalMelting range, capillary methodA pure crystalline solid of the expected substance; mixtures melt low or broad
TitrimetricAcid–base titration, dried basisAcid content and equivalent weight consistent with the molecule
Process profileChloride, sulfate, residue on ignition, HPLC scanNo salt load or process residue, and no co-eluting related substance

The layers are deliberately redundant. A blend can be made to titrate correctly by adding an acid, but the same blend rarely keeps a sharp melt, a matching IR and a low chloride figure at once. That redundancy is the point.

One mole of base per mole of acid

The titration rests on a fixed ratio: one mole of sodium hydroxide neutralises one mole of nicotinic acid. The equivalence weight is therefore 123.11 g/mol, and the assay is that measured acidity expressed as a percentage of the theoretical figure on the dried basis. The ratio is what makes the test specific to an acid of this size, and it is also what limits it.

A neutral diluent — lactose, dextrose, starch — consumes no base, so it lowers the assay and takes the melting range down with it. A nicotinate salt is already neutralised: sodium or calcium nicotinate does not titrate as the free acid, the pH of the dispersion turns alkaline, and the residue on ignition climbs with the metal. Niacinamide has no acid proton at all, so a blend of the two forms reads low on the titration even though both are vitamin B3.

The titration cannot separate the 3-isomer from the 4-isomer. Isonicotinic acid has the same molecular weight and the same acidic group, so it consumes base in the same ratio. What separates them is the IR spectrum and the melting range, which is why the identity layer is not optional for a material that is bought as a positional name.

X-ray diffraction and the solid form

Nicotinic acid is sold as a crystalline powder, and a diffraction pattern is a fingerprint of that crystal. X-ray diffraction confirms the crystalline phase, shows whether a second crystalline phase is present, and detects crystalline diluents such as lactose, dextrose or sodium chloride in a blend. It does not measure purity, and it is a poor detector of an amorphous filler, which scatters broadly rather than in sharp peaks.

Peak position is the identity information; peak width is not. A milled 80 mesh lot has smaller crystallites than a 40 mesh lot, so its peaks are broader, but the positions stay the same. A pattern with extra peaks at new positions is a different solid, not a different particle size.

The test earns its place in three situations: a new source that has not been audited, a lot whose melting range is broad, and a dispute where the other side's certificate shows a clean assay but an odd thermal result. Ask the laboratory to report the reference pattern it compared against.

The substitutions that turn up

Niacin substitutions · the signal and the test that catches it
SubstitutionWhat the buyer seesWhat catches it
Niacinamide blended inLow titration, low and broad meltMelting range, IR, HPLC
Sodium or calcium nicotinateLow titration, alkaline dispersion, higher residueResidue on ignition, pH, IR
Neutral diluentLow assay, melt depressed, loss on drying may riseAssay with IR; XRD for a crystalline filler
Inositol hexanicotinateVery low titration, poor solubility, low meltSolubility, assay, IR
Positional isomerAssay inside the windowMelting range, IR and UV

The last row is the one an assay-only programme misses. Every other row moves the titration, and most move the loss on drying or the residue as well. An isomer does not, so a certificate with a good assay and no spectral identity is not evidence that the material is the 3-isomer.

Writing the specification so the proof is possible

Specification wording should let a second laboratory reach the same answer. A workable line reads: “Niacin (nicotinic acid), CAS 59-67-6, 99.0–101.0% on the dried basis by titration, identification by IR and UV conforming to the reference, melting range 234–238 °C, loss on drying ≤1.0%, residue on ignition ≤0.1%, chloride ≤0.02%, sulfate ≤0.02%, heavy metals within the catalog panel, ≥95% through 40 mesh.”

Three habits make that line stronger. Name the form and the CAS number rather than the vitamin. Say which reference standard or monograph the identity comparison used. And state the basis for the assay, because an as-is figure and a dried-basis figure are not the same claim. The full limit set is on the COA page, and the specification terms are defined in the specification glossary entry.

Five questions for a supplier

First, which monograph edition or in-house method released this lot, and can the identification comparison be shown? Second, what was the melting range result for this lot, as a number rather than the range printed on the specification? Third, was the assay calculated on the dried basis, and what was the loss on drying? Fourth, are the chloride and sulfate lines results or “conforms”, and against which standard were they compared? Fifth, is the lot 100% nicotinic acid, or has it been blended or repacked since manufacture, and who manufactured it?

A supplier who answers all five has nothing to hide in the certificate. A supplier who answers only the assay has given a number, not an identity. The comparison between the two vitamin B3 forms is set out on the grade page and in the niacin vs niacinamide note; the infrared method itself is described in the FTIR method note, and the catalog limits are on the niacin product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation