02 Grade comparison

Niacin or niacinamide: choosing a vitamin B3 grade

Technical document 02 · Reviewed 2026-11-19 · Niacin

On this page
  1. Why “niacin” is not one grade
  2. The two forms side by side
  3. What the acid does to the matrix
  4. Matching the form to the dosage form
  5. How the grade is written into the specification
  6. When neither form is the right answer

Both materials are sold as vitamin B3, so the grade question is a molecule question. Niacin here means nicotinic acid, CAS 59-67-6: 99.0–101.0% by titration on the dried basis, melting 234–238 °C, sparingly soluble in water and acidic in solution. Niacinamide, CAS 98-92-0, is the amide: freely soluble, close to neutral and a different label ingredient. The choice follows the dosage form, the pH the matrix can carry and the ingredient name the label will use.

In one line

The grade question is not which powder is purer; it is which molecule the formula and the label can carry.

Why “niacin” is not one grade

Vitamin B3 is a family name, and it covers more than one substance. In the EU the permitted-forms list for niacin names nicotinic acid and nicotinamide; the US Supplement Facts line can read “Niacin (as niacinamide)”; the UK retains the same two entries. None of those texts use the acid and the amide interchangeably, because they are not: different CAS numbers, different melting ranges, different solubility, different behaviour in a blend.

A brief that asks for “vitamin B3, 100 mg” has not chosen a material. It has chosen a nutrient figure. The grade decision has to be made before the specification is written, because the certificate, the label and the release method all follow from it.

The two forms side by side

Niacin (nicotinic acid) and niacinamide · identity and handling
PropertyNiacin, nicotinic acidNiacinamide
CAS number59-67-698-92-0
Molecular formulaC6H5NO2C6H6N2O
Assay and method99.0–101.0% by titration, dried basis99.0–101.0% by HPLC
Melting range234–238 °C128–131 °C
Water solubilitySparingly solubleFreely soluble
Reaction in solutionAcidicClose to neutral
Flush, immediate releaseReported by many peopleNot reported at supplement doses

The melting range separates them by more than a hundred degrees, which makes a blend visible in a single test. The assay columns use different methods for the same reason: the acid carries a titratable proton, the amide does not.

What the acid does to the matrix

Nicotinic acid carries a carboxylic acid group that ionises in water, so it acidifies whatever it is dissolved or dispersed in. In a tablet that is usually tolerable; in a drink mix it is the first thing the formulator notices. The acid also reacts with alkaline ingredients. Sodium bicarbonate, calcium carbonate and magnesium hydroxide will neutralise it to a nicotinate salt, and a carbonate will release carbon dioxide while doing so. That reaction is not a defect in the raw material, but it changes the blend: part of the niacin is now a salt, the pH rises, and the taste shifts.

The amide has none of that chemistry. It dissolves readily, leaves the pH close to neutral and does not react with carbonate. The trade-off is physical: the amide is hygroscopic, so the pack and the dispensing room carry a moisture requirement that the acid does not, and a freely soluble powder dissolves rather than disperses, which changes the mouthfeel of a sachet.

Particle size belongs in the same conversation. The catalog grade is a crystalline powder at 40 mesh, milled to 80 mesh or granulated on request. At low doses per tablet, a finer powder distributes better; on a high-speed press, flow and segregation decide.

Matching the form to the dosage form

Tablets and capsules. The acid is the usual choice when the label says niacin and the dose is modest. It is a crystalline powder that runs on a tablet press at 40 mesh, and the acidity is buffered by the excipients around it. A coated tablet can keep the acid away from a sensitive ingredient in a combination.

Stick packs and drink mixes. The amide is easier: it dissolves clear, tastes neutral and does not drop the pH of the sachet. The acid works in a deliberately acidic matrix, such as a fruit-flavoured powder, where its sour note is part of the profile.

Effervescent systems. The acid and the carbonate in the system will react. A formulator can use that deliberately, but the label, the assay and the pH all have to be built around the salt that results; it is not a drop-in switch.

Gummies and chewables. The amide avoids the sour taste and the local acidity that a chewable can leave. The acid is workable only where the recipe already leans acidic and the taste has been built for it.

How the grade is written into the specification

The specification should name the molecule, not the vitamin. “Niacin (nicotinic acid), CAS 59-67-6, 99.0–101.0% on the dried basis by titration, melting range 234–238 °C, loss on drying ≤1.0%, chloride ≤0.02%, sulfate ≤0.02%, ≥95% through 40 mesh” leaves nothing to interpretation. A line that says only “niacin 99%” can be met by either molecule, and it gives the label no name to check.

Three details are worth writing down with it. State the assay basis, because as-is and dried figures differ by the water content. State the mesh, because it changes flow and content uniformity. And state which monograph or in-house method the release uses, so that a second laboratory can reproduce the result.

On the label, the form is part of the ingredient declaration. The nutrient figure is calculated in niacin equivalents, where both forms count one milligram as one milligram NE, so the number does not change when the form changes; the ingredient name does. That is why a late switch is a labelling event as well as a formulation one.

When neither form is the right answer

Some briefs are really a request for a different substance. Inositol hexanicotinate and other niacin esters are separate materials with their own specifications, and a request for a niacin product without the flush is usually a request for one of those or for the amide. The catalog niacin is the free acid, and it should not be sold as something else.

Where the formula cannot tolerate an acidic ingredient but the label can name any vitamin B3 form, the amide is the honest route, and the label reads niacinamide. A blend of the two forms is a third product again: it needs its own assay, its own label figure and its own stability data.

The forms are compared line by line on niacin vs niacinamide. The catalog limits are on the niacin product page, the release tests on the COA page, and the label and market rules on the compliance page. The specification terms themselves are defined in the specification glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation