06 Identity & adulteration

How we prove a lot is D-chiro-inositol, not myo

Technical document 06 · Reviewed 2026-11-20 · D-Chiro Inositol

On this page
  1. Five checks that have to agree
  2. The isomer ratio, not a counter-ion
  3. What diffraction can and cannot prove
  4. How substitution shows up
  5. Writing identity into the specification
  6. Five questions worth asking

D-chiro-inositol and myo-inositol are built from the same atoms and weigh the same, so no single number on a certificate separates them. Identity comes from several agreeing measurements: a chiral signal, a chromatographic separation that reports each isomer, a crystal pattern that confirms the solid, and a mass balance that accounts for the remainder. A total-inositol assay answers none of those on its own.

In one line

Identity here is the isomer, and the isomer needs more than a percentage: rotation for chirality, a resolving separation for the two peaks, and a mass balance for everything else.

Five checks that have to agree

Each check below answers a different question, and each can fail while the others pass. A supplier who has only the first has described a document, not a drum.

Checks for a D-chiro-inositol lot
CheckQuestionMethodWhat it establishes
Name and CASIs the isomer specified?Name, CAS 643-12-9Paperwork only
ChiralityIs the material optically active?PolarimetryA chiral cyclitol, not myo
SeparationHow much of each isomer?Resolving HPLCD-chiro and myo values
Solid formWhich crystal is present?X-ray diffractionThe phase, not the enantiomer
BalanceWhat else is in the drum?Assay, moisture, metals, sourceConsistency of the numbers

The isomer ratio, not a counter-ion

Myo-inositol has a plane of symmetry and is optically inactive; D-chiro-inositol does not, so its solutions rotate plane-polarised light. That is the first independent check. A powder that passes a summed inositol assay but shows no rotation has not shown the D-chiro isomer, however white and crystalline it looks.

The assay must report the two isomers as separate results. One inositol peak gives the sum, and the sum cannot tell a pure D-chiro lot from a blend. The resolving method needs a standard for each isomer, a demonstrated resolution and a stated detection limit; a spiked sample is the simplest proof that the separation works.

With two results in hand, the ratio is calculated from both and never by subtracting one from a total. A 40:1 formula is forty parts myo to one part D-chiro by weight, and because the masses are equal the molar ratio is the same. In a 4,100 mg total that is 4,000 mg myo plus 100 mg D-chiro, so the D form is 2.44% of the inositol mass.

Polarimetry is a screen rather than a complete chiral assay. It separates the D form from the L form by sign, and a racemate is inactive like myo, so a disputed chirality question needs chiral chromatography or NMR with a chiral shift reagent to close it.

What diffraction can and cannot prove

X-ray diffraction reads the packing of the solid. It shows whether the lot is crystalline, whether the pattern matches a reference, and whether a second crystalline phase is present above the method's detection limit. It does not measure the isomer ratio and it is not a purity assay.

There is a blind spot worth knowing. D-chiro and L-chiro are mirror images, and their crystals are mirror lattices that give the same powder pattern under ordinary laboratory conditions. Diffraction can therefore confirm the crystal form and expose a myo phase, but it cannot say which chiro enantiomer was weighed. Chirality has to come from rotation or a chiral separation.

Request the reference diffractogram and the limit of detection before accepting a match. A report that says “XRD conforms” without either has added very little. The technique is strongest when the question is solid form, crystallinity or a second phase, and when it is read beside the resolving assay and the rotation.

How substitution shows up

Signals of substitution in a D-chiro-inositol lot
SubstituteWhy it can pass a quick lookWhat gives it awayConfirming test
Myo-inositolSame formula, colour and solubilityA myo peak; no optical activityResolving HPLC with polarimetry
40:1 blend sold as D-chiroWhite powder at the same meshD-chiro value far below the labelResolving HPLC, two standards
Another cyclitol, such as pinitolPlant-extract origin; similar behaviourAn extra peak; source does not matchLC-MS and NMR
Maltodextrin or a sugarDilutes without changing appearanceAssay low; moisture or ash shiftsMass balance
L-chiro or a racemateSame formula and the same diffraction patternRotation reduced or reversedPolarimetry, chiral separation

Appearance is the weakest signal of all: both isomers are white to off-white and a blend can be milled to the same fineness. The strong signals are the separate isomer values, the rotation and the mass balance. A certificate that reports only appearance and a summed inositol figure has left the likeliest substitution untested.

Writing identity into the specification

  • “D-chiro-inositol, CAS 643-12-9, C6H12O6; source declared.”
  • “Assay ≥98.0% by an isomer-resolving HPLC method; column, mobile phase, detector and standard named.”
  • “Myo-inositol ceiling agreed per order and reported as a separate value.”
  • “Loss on drying ≤0.5%; melting point 225–230 °C; optical rotation reported.”
  • “Identification by HPLC retention and infrared spectrum; diffraction available on request.”
  • “Particle size ≥95% through 80 mesh; metals and microbiology as listed.”

Five questions worth asking

  1. Which isomer is this lot, and what CAS number appears on the certificate?
  2. How was the separation done, and what myo-inositol value did it return?
  3. What rotation was measured, and against which reference?
  4. What is the source, and which other cyclitols can that route bring through?
  5. Would you accept a joint re-test of the retained sample if we disagree about the isomer?

Direct answers to those five make an identity file; an assay percentage alone does not. The catalog entry is on the D-chiro-inositol page. The COA page places each result in its row; the level-four comparison follows through to the label; the methods section describes the separation; and the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation