02 Grade comparison

D-chiro-inositol supply forms: powder, granulation and the blend

Technical document 02 · Reviewed 2026-11-20 · D-Chiro Inositol

On this page
  1. An assay range is a gate, not a description
  2. The forms, and the blend that is not one of them
  3. Fineness, moisture and flow
  4. What the choice does in the finished product
  5. What the specification should say
  6. When a different purchase is the right one

D-chiro-inositol leaves the factory as a single-isomer powder, usually milled to 80 mesh, with a granulated option and with source and assay variants that change what else travels in the drum. A 40:1 myo blend is a separate formula with two label names, not a grade of this product. Within the single isomer, the choices that matter are the source, the mesh and the ceiling placed on myo-inositol.

In one line

The isomer is fixed; the variables that change a D-chiro-inositol purchase are the source, the mesh and the ceiling on myo.

An assay range is a gate, not a description

Two certificates can both read “D-chiro-inositol ≥98.0%” while one lot carries 1.4% myo-inositol and the other 0.2%. A third can be the same molecule recovered from plant material, with a different set of minor cyclitols and sugars. The percentage is the entry ticket; it does not describe the powder behind it.

The production route is the first hidden variable. D-chiro-inositol can be made by epimerising myo-inositol, or recovered from a plant source. Each route leaves its own minor profile: a plant extract can carry other cyclitols and residual sugars, while an epimerisation route has to control the isomer distribution. Neither route is inherently better, but the certificate has to match the route, and the specification has to name the source it was written around.

Presentation is the second variable. The catalog material is a powder at ≥95% through 80 mesh; a granulated version is a different specification with its own certificate. They are not two descriptions of one drum.

The forms, and the blend that is not one of them

D-chiro-inositol forms against the two-ingredient blend
OptionWhat it isLabel nameWhere it fitsWhat to watch
Single-isomer powder, 80 meshCatalog gradeD-chiro-inositolCapsules, tablets, stick packsMoisture pick-up; fine dust
Granulated single isomerAgglomerated powderD-chiro-inositolSachets and fast filling linesAny binder enters the label
Tighter myo ceilingSame isomer, narrower profileD-chiro-inositolLabels with an isomer claimDepends on the source route
40:1 pre-blendMyo plus D-chiro, weighed togetherBoth namesProducts that declare the ratioThe minor fraction can separate
Myo-inositolThe meso isomerMyo-inositolProducts built on myoA different ingredient entirely

The first three are one ingredient at different presentations. The blend is a formula and myo is another molecule, so treating either as a grade of D-chiro is how a label goes wrong.

Fineness, moisture and flow

An 80 mesh opening is roughly 177 µm. At that fineness the powder wets quickly, fills a small capsule evenly and blends well with other fine excipients, but it also throws dust, holds static and cakes once the pouch has been opened. D-chiro-inositol is hygroscopic, and a fine powder puts more surface in contact with humid air than a granulated one.

Granulation improves flow but adds a declaration. Agglomerated particles run more evenly on a sachet line and make less dust, but any binder used to build them joins the ingredient list. The assay and the moisture result belong to the granulated lot, not to the powder that entered the granulator.

Density is not in the catalog specification. If the filler or the sachet machine is sensitive to it, request bulk and tapped density on the actual lot. A new mesh or a granulation step is a new specification, not a packing note.

What the choice does in the finished product

In a capsule, fill weight, flow and moisture pick-up during the run are the practical constraints. The 80 mesh powder is the default; a granulated grade helps when the hopper bridges or the dust is unacceptable. In a tablet, compression and room humidity matter more than the last decimal of the assay, and a hygroscopic fill needs a short hold before the press.

In a stick pack, dissolution is rarely the limit because the powder dissolves to a clear solution. Wetting and clumping are the limit, and a granulated grade disperses more evenly than a very fine one. Taste and mouthfeel depend on the powder's fineness and the rest of the blend.

A 40:1 blend introduces a mixing problem. D-chiro is one part in 41, about 2.44% of the inositol mass, and a fraction that small can separate in a drum or a hopper. A 4,100 mg total carries 4,000 mg myo and 100 mg D-chiro. The blend needs a pre-blend, a granulated blend or a fixed mixing order, and the certificate should give a value for each isomer.

What the specification should say

  • “D-chiro-inositol, CAS 643-12-9, C6H12O6; source route declared.”
  • “Assay ≥98.0% by HPLC; column, mobile phase, detector and standard named.”
  • “Myo-inositol ceiling agreed per order and reported from a resolving method.”
  • “Loss on drying ≤0.5%; melting point 225–230 °C; metals and microbiology as listed.”
  • “Particle size ≥95% through 80 mesh; granulated on request, with the binder declared.”
  • “Destination market and label name confirmed before the order.”

“Inositol 98%” is not an adequate line. It leaves the isomer, the source, the mesh and the myo ceiling open, and a grade name left that open can cover a powder the label cannot declare.

When a different purchase is the right one

If the label says myo-inositol and the formula was built around the bulk grade, D-chiro is the wrong material however high the assay. If the label declares a 40:1 ratio, buying the single isomer and adding myo in-house is possible, but the blend then belongs to the buyer's process, and the supplier's certificate no longer covers the ratio.

A tighter myo ceiling is worth buying when a label or a customer specification depends on it. Granulation is worth buying when flow, dust or density is the real constraint. Neither is a quality upgrade on its own, and neither replaces a certificate that matches the drum.

The catalog specification sits on the D-chiro-inositol product page; the release lines are on the COA page; the isomer question is taken further on the D-chiro versus myo page; the other isomer is described on the inositol product page; release practice is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation