03 Stability

Ubiquinol oxidises back to ubiquinone; the pack sets the shelf life

Technical document 03 · Reviewed 2026-11-20 · Ubiquinol

On this page
  1. The sealed powder and its exposures
  2. The oil, the softgel and the process heat
  3. The variables that move the assay
  4. Designing the stability run
  5. What the finished format adds
  6. Where the retest period comes from

Ubiquinol is the reduced form of coenzyme Q10 and it oxidises back to ubiquinone. The powder and the oil therefore fail in the same direction: the ubiquinol assay falls, the ubiquinone figure rises, and the colour moves towards yellow-orange. The pack, the headspace and the storage temperature decide how fast that happens; the certificate only describes the lot at release.

In one line

Ubiquinol fails by oxidising to ubiquinone, so the pack, the headspace and the storage temperature are the shelf life.

The sealed powder and its exposures

Loss on drying is capped at ≤5.0% in the catalog. It is a gate at release, not an allowance for storage. An opened foil pouch takes up moisture from the air, and the powder's surface is also exposed to oxygen; the two together move the assay. Store the powder in the light-resistant pouch supplied, or in another sealed opaque container; write the opening date on the pack.

Light is the second driver. A clear jar on a bench is an exposure even when the lid is on. Heat raises the rate of oxidation and can soften or melt the powder at the top of a warm store; ubiquinol melts at about 49 °C, so a loading bay or a car boot in summer is a real risk.

Colour is a useful early signal: white to pale yellow is the reduced form, and a shift towards orange suggests oxidation. It is not a release test, because a batch can darken without a matching change in the ubiquinone figure.

The oil, the softgel and the process heat

Ubiquinol is not used as an aqueous solution; it is fat-soluble and practically insoluble in water. The practical “solution” is an oil: a softgel fill, an oil blend or an emulsion. In oil, oxygen is dissolved in the carrier, and the oil's own oxidation products can consume the ubiquinol. The carrier, the headspace and the fill temperature all belong to the stability question.

Heat arrives with the process, not only with the store. A warm blend or a hot fill puts the oil through a thermal load that the bulk powder never meets, and the hold time before filling belongs to that same exposure. Light and metal ions, iron and copper above all, speed the oxidation; clean stainless steel is not the same as a corroding fitting.

A softgel protects the fill from air after sealing, but the shell is not an absolute barrier to oxygen and moisture. The finished-product stability belongs to the softgel, not to the bulk oil, and the two should not be conflated.

The variables that move the assay

What moves ubiquinol in storage
FactorWhat it doesControl
OxygenOxidises ubiquinol to ubiquinoneSealed pack; low headspace; nitrogen where specified
LightAccelerates oxidation; colour shiftFoil or opaque pack; dark store
HeatRaises the reaction rate; melts powder near 49 °CControlled store; cool process
MoistureRaises loss on drying; exposes fresh surfaceSealed pouch; desiccant where needed
Metal ionsCatalyse oxidation, especially iron and copperAvoid contact; check equipment and colourants
Oil qualityPeroxides in the carrier consume ubiquinolCarrier specification; peroxide value
pH in emulsionAlkaline conditions destabilise the reduced formValidate the emulsion pH and hold time

None of those factors acts alone. A store that is simultaneously warm, bright and damp is worse than three separate stresses; a carrier with a high peroxide value consumes the ubiquinol from within. The useful question is not whether ubiquinol is stable as a material, but how long it remains reduced in a specified pack under a specified condition.

Designing the stability run

A protocol is usable when it fixes the pack, the condition, the time points and the test panel. Warehouse conditions are represented by 25 °C/60% relative humidity, with 30 °C/65% relative humidity as the intermediate case; 40 °C/75% relative humidity is the accelerated arm that stresses the pack. Add a light-exposure arm, because a dark incubator misses the failure mode that matters most.

Test ubiquinol, ubiquinone, appearance and loss on drying at each point, plus microbiology where the pack is opened. For an oil or a softgel, add the carrier's peroxide value and acid value, and test the finished fill rather than the bulk oil. Report the individual figures, not a single pass note.

Request the stability summary for the pack on the purchase order. A 1 kg pouch and a 25 kg drum have different headspace and different opening histories; a softgel has a shell that the drum does not. The data belongs to the pack, not to the product family.

What the finished format adds

Capsules and tablets begin dry, but capsule shells and tablet excipients can still pass moisture into the fill, and compression adds both heat and pressure. Check the ubiquinone figure at release and again after storage, along with the appearance of the powder. A tablet that carries a metal-containing colourant adds a contact that the bulk powder did not have.

An oil blend or a softgel adds the carrier's oxidation state. A highly unsaturated carrier oxidises, and its peroxides can consume the ubiquinol; a saturated or monounsaturated carrier is less reactive but not inert. Any overage is the formulator's call, and it is a label and stability decision; it cannot compensate for a pack that admits oxygen.

An emulsion adds pH and interfacial area. Alkaline conditions destabilise the reduced form, and a high-shear step adds oxygen. Bulk data is a starting point; the answer comes from the finished matrix.

Where the retest period comes from

No single shelf-life figure is published for ubiquinol; the pack and the storage condition determine it. The specification states the retest period, and the stability file for that pack supports it. A shelf-life figure without a named pack, a defined condition and a stated test panel is only an assertion.

Extending use beyond the retest period requires a fresh assay of the retained sample. Never assume an extension, and never move a bulk figure onto a repacked container. The standard packs appear on the product hub; the release tests are set out on the COA page; pack sizes and lead time are on the MOQ page; the analytical methods are collected under methods; the release workflow is described on quality.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation