How we prove a ubiquinol lot is the reduced form
A ubiquinol lot is the reduced form when four lines agree: the document names ubiquinol and CAS 992-78-9, the HPLC retention and UV spectrum match the ubiquinol reference, the ubiquinone fraction is inside the ≤2.0% limit, and the assay, moisture and impurities close the mass balance. A “CoQ10” assay alone cannot separate ubiquinol from ubiquinone; the redox pair has almost the same mass.
Identity is the ubiquinol peak, the ubiquinone ratio and the mass balance agreeing; a CoQ10 assay alone cannot tell which form is in the drum.
Four checks that must agree
Each check answers a different question, and an answer that stops at the document layer describes the paperwork, not the drum.
| Check | Question | Evidence | What it establishes |
|---|---|---|---|
| Paper trail | Does the paperwork name the redox form? | Name, CAS 992-78-9, formula | Only that the documents agree |
| HPLC and UV | Is the peak ubiquinol? | Retention time and spectrum against a ubiquinol standard | The molecule and its redox state, when both forms are resolved |
| Oxidation | How much ubiquinone is present? | Separate ubiquinone peak | The reduced fraction |
| Mass balance | Is the material diluted or wet? | Assay, loss on drying, impurity profile | Whether the numbers fit together |
The ubiquinone ratio
The ubiquinone figure is the ratio that matters. At the two limits — 95.0% ubiquinol and 2.0% ubiquinone — the ubiquinone/ubiquinol ratio is about 0.021; at 99.0% and 0.5% it is about 0.005. Both can pass an assay floor, but they are not the same powder.
The ratio also separates oxidation from dilution. Oxidation raises ubiquinone while the total CoQ10 stays roughly constant; dilution lowers both ubiquinol and ubiquinone and leaves the ratio roughly normal. A low ubiquinol figure with a low ubiquinone figure is more likely a carrier or a moisture problem than an oxidation problem.
Report the two figures separately and state the basis. A single “total CoQ10” number hides the ratio, which is the specification that defines the reduced form. The same logic explains why a 275 nm assay calibrated for ubiquinone needs its own standard and wavelength before it can report ubiquinol.
What XRD can and cannot show
XRD asks whether the powder has a crystal lattice and whether that lattice matches a ubiquinol reference. The reduced form is a low-melting solid, and a carrier-based powder will show the carrier's peaks alongside or instead of the ubiquinol pattern. A claim of a match is thin without the pattern, the reference and the detection limit.
XRD is not a release test for this product, and it does not measure the ubiquinone fraction. It is useful when the question is whether the material is crystalline ubiquinol, an amorphous dispersion or an oil-filled powder, and when two sources are being compared. In a dispute, the diffraction pattern, the chromatogram and the ubiquinone ratio together carry more weight than any single result.
The substitutions to watch for
| Substitution | What it does | Signal | Test |
|---|---|---|---|
| Ubiquinone | Oxidised form; more stable, same tail | Ubiquinone above 2.0%; assay split shifts | Dual-wavelength HPLC; ratio |
| Dilution | Lowers active per gram | Ubiquinol low; ubiquinone low; ash or carrier present | Mass balance; loss on drying |
| Oxidised lot | Passed at release, aged in store | Ubiquinone high; colour orange | HPLC; retained sample |
| Derivative | Different molecule, such as an acetate | Extra peak; no free ubiquinol | HPLC; NMR or high-resolution MS |
| Carrier oil | Changes assay per gram | Assay low; oil present | Extraction; carrier specification |
Colour is the weakest signal: white to pale yellow covers a range, and an orange tint can come from oxidation or from a carrier. The evidence that counts is the ubiquinone ratio, the chromatogram and the mass balance. A certificate with appearance and a total CoQ10 number has not tested the substitution most likely to occur.
Identity lines for the specification
- “Ubiquinol, CAS 992-78-9, C59H92O4, reduced form.”
- “Assay ≥95.0% by HPLC, with the basis stated; ubiquinone ≤2.0% by HPLC.”
- “Identification by HPLC retention and UV spectrum; name the wavelength or detector.”
- “Loss on drying ≤5.0%; heavy metals and microbiology as listed.”
- “Powder ≥95% through 80 mesh; oil grade: carrier and fill weight stated.”
- “No ubiquinone above the stated limit; no carrier or derivative not declared.”
What the supplier should be able to answer
- Which redox form is this lot, and which CAS number is on the certificate?
- May I see the chromatogram used for the ubiquinol result, not just the percentage?
- What is the ubiquinone result for this lot, and how was the sample protected from air and light?
- What is the loss on drying, and is the assay reported as-is or on the anhydrous basis?
- Would you agree to a joint re-test of the retained sample if the result is challenged?
Those five answers together make an identity file; one assay figure does not. Catalog data is on the product hub; the COA page shows where each result sits; the grades page compares the presentations; the level-four page covers the redox choice; the analytical methods are under methods.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation