03 Stability

NMN is hygroscopic and pH-sensitive; the pack decides the shelf life

Technical document 03 · Reviewed 2026-11-19 · NMN

On this page
  1. The powder and the pack
  2. After the powder dissolves
  3. What makes NMN fail
  4. A stability protocol for the pack
  5. What the formula adds
  6. From data to a shelf life

NMN is hygroscopic and its 5% solution is acidic, at pH 2.0–4.0. The dry powder keeps when the pack excludes water; in solution, hydrolysis and anomerisation set the clock. A shelf life is a property of the pack and the storage condition, not of the drum label alone.

In one line

The powder keeps only as dry as the pack keeps it; water, acid and heat set the shelf life, not the drum label.

The powder and the pack

The catalog water limit is ≤5.0% by Karl Fischer. That is a release gate, not a storage target. A powder near the water limit has little headroom; in a humid dose room it can move past the limit before the capsule is filled. Store the sealed pack in a cool, dry place, away from direct light, and keep the pack closed between weighing and sealing. Where a desiccant is fitted, it belongs in the pouch, not in a bin beside it.

NMN is freely soluble in water, so a damp powder can cake and the water result can climb without any visible change. The pack is part of the specification: a 1 kg foil pouch and a 25 kg fiber drum have different headspace, different opening cycles and different moisture ingress paths.

After the powder dissolves

Once dissolved, NMN has two hydrolysis routes. The phosphate can be removed to give nicotinamide riboside, and the glycosidic bond can split to give nicotinamide. The α and β anomers can also equilibrate in solution. Acid, heat and time push all three. The pH 2.0–4.0 release window describes the lot at release; it is not a stability target.

A drink mix is a solution in the making. A dry blend has a low water activity and a long hold; a mixed drink has a short one. The formulation should specify the water activity of the dry mix, the pH after dispersion, and the maximum hold time before filling or drinking. A powder stick is the lower-water format, but its headspace and seal still decide the shelf life.

What makes NMN fail

Stability factors for NMN powder and for a dissolved mix
FactorWhat it changesControl
WaterHydrolysis, caking and the Karl Fischer resultSealed pack, desiccant where fitted, low room humidity
pHHydrolysis and anomerisation rateMeasure the 5% solution and the dispersion, not only the powder
HeatReaction rate and colourCool store; limit process temperature and hold time
LightColour and degradationOpaque pack; keep away from direct light
Time in solutionHydrolysis and the α/β balanceSet a maximum hold time and test at the end of it

The weight of these factors depends on the pack and the formula. A sealed powder at 25°C/60% relative humidity is a different system from a drink mix at 40°C. The protocol has to test the system that will be sold, not the powder in a glass jar.

A stability protocol for the pack

Run the protocol in the final pack. A workable design follows ICH Q1A(R2): long-term at 25°C/60% relative humidity, intermediate at 30°C/65%, and accelerated at 40°C/75%, with test points at 0, 3, 6, 9 and 12 months for long-term and 0, 1, 2, 3 and 6 months for accelerated. For a food ingredient this is a design model, not a regulatory claim; the destination market may ask for a different set.

At each point test appearance, purity by HPLC, the α/β ratio by NMR, water by Karl Fischer, pH of a 5% solution, microbiology and pack integrity. Add a note on caking and a photograph of the opened pack. The anomer and water results can move before the HPLC purity does, so a protocol that tests only purity can miss the failure.

Run at least three lots. If the customer will open a drum over weeks, add an opened-and-resealed arm on a defined schedule. That arm is where dose-room behaviour shows, and it is an arm often left out of a supplier data pack.

What the formula adds

The formula adds water and pH. Hygroscopic excipients, alkaline salts and any water-based granulation or coating step shorten the window. An acidic NMN powder can also shift the pH of a low-buffer blend, so measure the pH of the dispersion, not only the powder.

Check the process temperature and the time the powder spends in the blender. A short, dry blend is easier on the material than a wet granulation. If the formula needs a liquid step, ask for compatibility data on the finished blend, not only on the raw material.

The finished product's shelf life is not the ingredient's shelf life. The brand owns the finished-product study; the supplier's data supports it.

From data to a shelf life

Assign the shelf life per pack format from the protocol. The catalog page does not promise a fixed number of months, because the number depends on the pack, the storage condition and the market's rules. A 1 kg foil pouch, a 25 kg drum and a stick pack are three different packages.

After opening, the clock restarts. A drum opened daily in a humid room is not the same package that was tested sealed. Write the opening and resealing instruction, the desiccant replacement where fitted, and the maximum time out of the pack. Do not extend a shelf life on a purity result alone; water and pH can fail first.

Keep the stability data with the lot and the pack code. If the pack changes, the data does not transfer automatically.

The catalog specification is on the NMN product page. The certificate lines are on the COA page; the presentation choices are on the grade page. The release and sampling process is set out on the quality page, and the published specifications are in the specification index.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation