How we prove an NMN lot is β-NMN
β-NMN is an anomer plus a phosphate, so the identity file has to establish both. HPLC with a standard shows that the main peak is NMN; 1H NMR shows the ribose anomer and the phosphate environment. A purity percentage on its own cannot separate those questions, and a certificate that says only “NMR conforms” leaves the anomer open.
β-NMN is proved by the anomer and the phosphate together; a 98% HPLC peak can belong to the wrong anomer or the wrong nucleotide.
Four checks, one file
| Layer | Evidence | What it closes |
|---|---|---|
| Document | Lot code, COA, specification and chain of custody | Which material was tested |
| Chromatography | Retention time, UV spectrum and a spike with a standard | The main peak is NMN, not a co-eluting analog |
| NMR | 1H spectrum; 31P where available; anomer integrals | Structure, phosphate and the α/β ratio |
| Concordance | Appearance, pH, water and solubility | The solid matches the rest of the file |
The four checks answer different questions, so a single result can satisfy one and leave the rest untouched. A retention time can match while the anomer is wrong. An NMR spectrum can match the structure while the lot carries several percent water. The file is the combination.
pH and water are the concordance layer. A 5% solution at pH 2.0–4.0 and water ≤5.0% match the catalog solid. A pH outside the range or a high water result does not identify a different nucleotide, but it does say the lot is not the solid the file describes.
The α/β ratio
NMN has an anomeric centre, and the β anomer is the form named in the specification. The α anomer has the same mass and a similar UV spectrum; on a column that does not resolve the two, it can sit inside the main peak. NMR can read the anomeric proton integrals, so it is the method that answers the α/β question.
Sample preparation matters. The anomers can equilibrate in solution, so a spectrum run after a long hold can show a different ratio from the solid. The laboratory should state the solvent, the temperature and the time between dissolution and acquisition. A ratio without those details is not comparable between laboratories.
The specification should state the ratio and the method. An α limit is agreed case by case; it is not implied by the word “β”. If the certificate says “β-NMN” and reports no ratio, the buyer has a name, not a measurement.
What XRD adds, and what it does not
X-ray diffraction is a fingerprint of the crystalline solid. A pattern that matches a β-NMN reference supports the identity of the solid form, and extra crystalline peaks can flag a crystalline diluent. It is a useful support test because it looks at the packed solid, not a solution.
It stops at three places. Routine XRD does not quantify the α/β ratio, because it identifies a crystalline phase rather than the anomer content of a mixture. It is blind to amorphous material, so a negative finding is not a purity result. And it does not replace Karl Fischer for water. For NMN, NMR is the anomer method and Karl Fischer is the water method; XRD is the solid-form check.
XRD alone is not the proof of β-NMN. Ask for the NMR spectrum and the ratio.
How NMN can be substituted
| Adulterant or route | What it does | What catches it |
|---|---|---|
| Nicotinamide riboside | Lacks the phosphate and is smaller | HPLC retention; 31P NMR or a phosphate assay |
| Nicotinamide adenine dinucleotide | Adds a second nucleotide unit | HPLC gradient; NMR signals |
| Nicotinamide | Hydrolysis product, small and early eluting | HPLC related substances; a spiked sample |
| α-NMN | Same mass, wrong anomer | NMR anomer integrals |
| Dilution | Water, maltodextrin or a phosphate salt | Karl Fischer, mass balance, phosphate |
The dilution route is the one a purity figure hides most effectively. HPLC area normalisation sees only the peaks that absorb at the detection wavelength. Water, a salt or a non-UV carrier can be invisible, so a 98.0% area result can sit on a lot with a much lower NMN content per gram. The certificate needs water, a mass balance or an assay against a standard, and a statement of what else is in the drum.
An adulterant that co-elutes is harder. A method that does not resolve nicotinamide riboside from NMN will report one peak as NMN. Ask for the chromatogram, the resolution from the nearest related peak, and a spiked sample. The same principle applies to the dinucleotide: a gradient that runs long enough to see it is part of the method.
The lines that make β testable
| Line | Method | Limit or requirement |
|---|---|---|
| Identity | HPLC retention and UV; 1H NMR | Conforms to the β-NMN standard |
| Purity | HPLC | ≥98.0% area |
| Anomer ratio | 1H NMR | β/α reported; limit agreed |
| Water | Karl Fischer | ≤5.0% |
| pH | Potentiometry, 5% solution | 2.0–4.0 |
| Heavy metals | ICP-MS | Lead ≤3 · arsenic ≤2 · cadmium ≤1 · mercury ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
The order of the lines matters less than the method column. An identity line without a method is a name. A purity line without a basis is a number. The anomer line is the one that makes the β claim testable.
Five questions that close the file
- What is the β/α ratio by 1H NMR on this lot, and can you send the spectrum with the integrals?
- What is the HPLC method — column, mobile phase, wavelength, standard and integration — and does it resolve nicotinamide riboside and nicotinamide?
- What are the water by Karl Fischer and the pH of a 5% solution on this lot?
- What are the phosphate, related-substance and residual-solvent profiles, and is the material the free acid or a salt?
- Does the COA belong to the drum being shipped, and can you supply a retained sample and an independent identity report?
Five clear answers amount to an identity file. A single purity percentage does not. The certificate lines are on the COA page; the presentation choices are on the grade page; the comparison with nicotinamide riboside is on the NMN versus NR page. The catalog specification is on the NMN product page, the lot-release process is set out on the quality page, and the published specifications are in the specification index.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation