06 Identity & adulteration

How we prove a lot is whey protein hydrolysate

Technical document 06 · Reviewed 2026-11-20 · Whey Protein Hydrolysate

On this page
  1. Four questions an identity file has to answer
  2. The ratios that carry the evidence
  3. X-ray diffraction: what it can and cannot show
  4. What adulteration looks like
  5. Identity clauses for the specification
  6. Five questions for the supplier

A whey protein hydrolysate lot is the named material when four things agree: the documents name the grade and the degree of hydrolysis, the protein profile matches a reference, the hydrolysis figure sits inside the agreed band, and the nitrogen result supports the protein figure on its dry basis. The assay alone cannot separate a hydrolysate from an isolate, because both are whey protein and both pass a Kjeldahl test. The hydrolysis evidence is what makes the claim.

In one line

A hydrolysate is proven by three measurements that agree: the protein profile, the degree of hydrolysis, and the nitrogen figure the protein was calculated from.

Four questions an identity file has to answer

A certificate can name the correct material and still prove nothing about the powder. The four below are separate questions, each needing its own evidence. The CAS number on the record, 84082-51-9, names the whey protein mixture rather than a single molecule, so it identifies the ingredient family and never the lot.

Four pieces of evidence for whey protein hydrolysate identity
EvidenceQuestion it answersTestWhat it establishes
PaperworkAre the grade and the hydrolysis named?Name, CAS, degree of hydrolysisPaperwork only
Protein profileIs the protein whey?Electrophoresis or HPLC against a referenceThe protein source
HydrolysisIs it a hydrolysate, and how far gone?Degree of hydrolysis and peptide distributionThe process, not the source
Mass balanceIs it diluted or spiked?Protein, moisture, fat, lactose, ash, nitrogenConsistency of the numbers

The second and third rows answer different questions, and a supplier who provides only one has answered only half of the page. An isolate can match the protein profile exactly; a hydrolysate made from soy would fail it.

The ratios that carry the evidence

The protein figure is a ratio: nitrogen × 6.38 for milk protein. At 80.0% protein on a dry basis the powder should report about 12.5% nitrogen, and at 5.0% moisture the as-is protein is 76.0%. A certificate that reports protein without the nitrogen figure leaves the reader unable to repeat the calculation, and a nitrogen figure far above 12.5% for a declared 80.0% protein points to nitrogen that the amino acids do not account for.

The second ratio is the hydrolysis itself. The degree of hydrolysis is the share of peptide bonds cleaved, so it is a ratio by definition, and the peptide distribution adds the share of the protein mass below a stated molecular-weight cut-off. The two belong together: a degree of hydrolysis near 20% describes an average, and a size-exclusion profile shows whether the mass sits in short peptides or in a long tail. The HPLC method note covers the separation.

A third ratio is worth asking for when the numbers look too good: non-protein nitrogen as a share of total nitrogen. Whey carries some non-protein nitrogen naturally, but free amino acids and other nitrogen sources inflate the Kjeldahl figure without adding protein. The amino-acid profile is the check, because a nitrogen total that the profile cannot account for is the signature of a spike.

X-ray diffraction: what it can and cannot show

A spray-dried protein powder is amorphous, so X-ray diffraction cannot identify the protein and is not a release test for it. What it can show is a crystalline phase that should not be there: crystalline lactose from a dilution, or a crystalline amino acid such as glycine or taurine added to raise the nitrogen figure. The XRD method note describes the measurement.

Read a diffraction statement with care. “XRD conforms” without the reference pattern and the detection limit says little, and a mostly amorphous halo is the expected result for a hydrolysate, not a finding. Ask what the laboratory was looking for before accepting that it found nothing. For a disputed lot, XRD plus a peptide distribution plus the nitrogen balance is stronger than any one of the three.

What adulteration looks like

Substitutions to test for in a whey protein hydrolysate
AdulterantWhat it doesSignalTest
Whey isolate sold as hydrolysateSame protein, no hydrolysisLow degree of hydrolysis; no bitternessDH assay, peptide distribution
Free amino acidsRaises the nitrogen figure without whey proteinNon-protein nitrogen high; free amino acid peaksAmino-acid profile, NPN
Non-protein nitrogenInflates Kjeldahl without proteinNitrogen above what the profile explainsKjeldahl plus amino-acid profile
Lactose or maltodextrinDilutes the proteinProtein low; lactose or sugar high; ash lowHPLC sugars, mass balance
Soy or pea proteinCheaper protein sourceProtein profile differs; amino-acid pattern shiftsElectrophoresis, ELISA
A different hydrolysis bandPasses the name, not the behaviourDH outside the agreed band; taste differsDH assay against the agreed method

Bitterness is a weak signal on its own, because a bitter note can come from the enzyme or the matrix, and a bland hydrolysate is not automatically an isolate. The stronger signals are the hydrolysis figure, the peptide distribution and the nitrogen balance. A certificate that reports protein and appearance but no hydrolysis has not tested the substitution that matters most here.

Identity clauses for the specification

  • “Whey protein hydrolysate, protein ≥80.0% on a dry basis, Kjeldahl N × 6.38; report the nitrogen figure.”
  • “Degree of hydrolysis 15.0–25.0% by a named method; report the result, not only conformity.”
  • “Peptide distribution by size-exclusion HPLC against the approved sample.”
  • “Protein profile against a reference; no foreign protein detected.”
  • “Moisture ≤5.0%; fat ≤2.0%; lactose ≤2.0%; ash and sodium as agreed.”
  • “Lot code and pack recorded; retained sample kept for the agreed period.”

The hydrolysis clause and the taste clause belong together, because a specification that fixes the number and not the flavour can be met by a lot nobody wants to use.

Five questions for the supplier

  1. What is the degree of hydrolysis for this lot, by which method, and what is the result?
  2. Can you provide the peptide distribution, not only the hydrolysis percentage?
  3. What is the nitrogen figure behind the protein result, and was any non-protein nitrogen measured?
  4. Does the protein profile match the reference, and which method produced it?
  5. Would you accept a joint re-test of the reserve sample if a result is disputed?

Those five answers together make the identity file; a protein percentage on its own does not. The product page carries the catalogue specification; the COA page marks where each figure appears; the grades page explains the hydrolysis band; the comparison with the isolate covers what the name does not tell you; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation