02 Grade comparison

Choosing a whey protein hydrolysate grade

Technical document 02 · Reviewed 2026-11-20 · Whey Protein Hydrolysate

On this page
  1. Why the family is graded by hydrolysis
  2. Where the hydrolysate sits in the whey family
  3. Standard powder and instantized powder
  4. What the grade does to the dose
  5. What to write into the specification
  6. When the hydrolysate does not fit

A whey protein hydrolysate is chosen for its degree of hydrolysis and its powder form, not for its protein percentage: the catalogue floor is 80.0% on a dry basis, the same as a concentrate, while the hydrolysis band runs from 15.0% to 25.0%. Inside that band the peptide profile, the bitterness and the mineral residue move, and those are what a formula depends on. The grade name has to carry the hydrolysis figure for the same reason.

In one line

The grade of a whey hydrolysate is set by its degree of hydrolysis, not by its protein percentage, because the protein floor is the same across the family.

Why the family is graded by hydrolysis

A hydrolysate is made by treating whey protein — usually a concentrate or an isolate — with a food-grade protease at a controlled pH and temperature, then inactivating the enzyme and drying the liquor. The protein is not concentrated by that step; it is cut. That is why a hydrolysate and a concentrate can both sit at 80.0% protein on a dry basis and still behave differently in water and on the tongue.

The degree of hydrolysis is the figure that names the grade. A powder at the lower end of the band keeps more intact protein, tastes milder and behaves more like an isolate. A powder at the upper end has more short peptides, a stronger savoury or bitter note and a higher osmolality at the same protein dose. Both are inside the catalogue specification, and a buyer who orders “hydrolysate” without a hydrolysis figure has not chosen between them.

Two further choices ride on the same grade name. The enzyme selection changes which peptides are produced, so two powders at the same degree of hydrolysis can differ in bitterness. The neutralisation step leaves a mineral salt and moves ash and sodium. Neither appears in the protein figure.

Where the hydrolysate sits in the whey family

Whey protein hydrolysate, isolate and concentrate · catalogue limits
PropertyHydrolysate 80Isolate 90Concentrate 80
Protein, dry basis≥80.0%≥90.0%≥80.0%
Degree of hydrolysis15.0–25.0%Not applicableNot applicable
Fat≤2.0%≤1.0%≤6.0%
Lactose≤2.0%≤1.0%≤5.0%
AshAgreed separately≤3.0%≤4.0%
Taste in waterMild to savoury, bitter at higher hydrolysisBland, milkyMilky, slightly cooked
Clarity in waterClear to slightly opalescentSlightly opalescentOpaque
Main useClear drinks, sticks, acidified systemsClear drinks, bars, high-protein claimsOpaque shakes, bars, bakery

The ash line is the one to watch when the grade is switched. The isolate and the concentrate carry a catalogue ash ceiling; the hydrolysate here does not, because neutralisation makes the figure process-specific. If the formula has a mineral budget, agree the ash and sodium limits in writing rather than assuming the isolate figure carries over.

Standard powder and instantized powder

The catalogue form is an 80 mesh powder, ≥95% through the sieve. It disperses freely in water and gives a clear to slightly opalescent solution, which is the practical reason a hydrolysate is chosen for a clear or acidified drink. The powder is hygroscopic: an open pouch takes up moisture, the particles stick and the bag sets, and the moisture figure on the certificate stops describing what is in the drum.

An instantized version is available on request. Agglomeration makes the powder wet faster and produce less dust on a filling line, but it changes the particle-size line, so it is a different specification rather than a packing option. If the instantizing aid is lecithin, the powder may carry a soy-derived carrier, and the allergen statement has to be checked. That is a label change, not only a line change.

Foaming is the other physical behaviour to test: whey proteins foam when mixed or pumped, and the peptide profile changes how much. A powder that foams heavily in a pilot mixer can leave the filler short of volume, so the trial should measure foam.

What the grade does to the dose

Protein per serving is the same arithmetic across the family: the as-is protein is the dry-basis figure minus the moisture. At the 5.0% moisture limit the hydrolysate is 76.0% protein as weighed, so a 20 g protein serving needs 26.3 g of powder. The isolate at its 90.0% floor and the same moisture needs 23.4 g.

What 20 g of protein carries at the catalogue limits
Per 20 g proteinHydrolysate 80Isolate 90Concentrate 80
Powder needed26.3 g23.4 g26.3 g
Fat at the limit0.53 g0.23 g1.58 g
Lactose at the limit0.53 g0.23 g1.32 g

The hydrolysis figure does not change that arithmetic, but it changes the osmolality of the drink. Hydrolysis multiplies the number of dissolved particles per gram of protein, so a hydrolysate drink at 20 g protein carries a higher osmotic load than the same drink built on an isolate. The formulator feels it as taste and mouthfeel; the comparison with the isolate takes the point further.

A capsule or tablet carries a small dose, so it suits a product where the hydrolysate is one ingredient among several rather than the protein source. For a protein dose the stick pack and the drink mix are the practical formats, and both need the powder to disperse without lumps.

What to write into the specification

  • “Whey protein hydrolysate, protein ≥80.0% on a dry basis, Kjeldahl N × 6.38.”
  • “Degree of hydrolysis 15.0–25.0%, method named on the certificate.”
  • “Peptide distribution by size-exclusion HPLC reported; bitterness checked against the approved sample.”
  • “Moisture ≤5.0%; fat ≤2.0%; lactose ≤2.0%; particle size ≥95% through 80 mesh.”
  • “Ash and sodium agreed separately if the formula or the label needs them.”
  • “Milk allergen statement, origin and pack, and whether the grade is standard or instantized.”

The degree of hydrolysis and the bitterness belong in the same clause. A specification that fixes the number but not the taste can be met by two lots a consumer would not accept as the same product.

When the hydrolysate does not fit

If the formula is a neutral, opaque shake and nothing on the label depends on hydrolysis, an isolate or a concentrate is simpler: the taste is blander, the ash is capped and the specification is shorter. If the bitterness cannot be masked at the dose, a lower degree of hydrolysis or a different enzyme is the fix, and that is a grade change rather than a flavour change.

If the finished product is an infant formula, the category is regulated separately and this food-grade specification does not cover it. If the label names an isolate, a hydrolysate is not a drop-in, even though both are whey protein. And if the hope is that hydrolysis removes the milk declaration, the grade cannot deliver that; the compliance page explains why.

The product page carries the catalogue specification; the COA page shows how the two figures are reported; the stability page covers the moisture and heat risk; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation