02.1 WPC vs WPI

WPC 80 vs WPI 90: protein, lactose and the label

Technical document 02.1 · Reviewed 2026-11-19 · Whey Protein Concentrate

On this page
  1. The protein figure and what the grade number means
  2. Lactose and fat at the dose
  3. What changes in the glass and on the line
  4. How the two are declared
  5. What the regulation does not change
  6. When to choose each

WPC 80 and WPI 90 differ by about ten points of protein, four points of lactose and five of fat, all measured on the same dry basis. Those gaps change how much powder a serving needs, how clear the drink is and what the label can say. Once the dose is fixed, the protein figure is the least interesting of the differences.

In one line

The choice between WPC 80 and WPI 90 is made on lactose, fat and clarity at the dose, and only then on the protein figure that appears on the label.

The protein figure and what the grade number means

Both numbers are dry-basis floors, not the protein in the powder as sold. WPC 80 is at least 80.0% protein on a dry basis and WPI 90 at least 90.0%, both calculated with Kjeldahl nitrogen and the 6.38 factor for milk protein. At the 5.0% moisture limit those become 76.0% and 85.5% as-is, because the water in the powder dilutes the figure.

The grade number is also a floor rather than a measurement. A lot at 83% protein can still be sold as WPC 80 if the specification says ≥80.0%, and a lot at 81% is not a worse material than one at 84% unless the specification says so. What the buyer should compare is the release limit and the lot result, not the number in the product name.

The dose arithmetic is where the ten points turn into grams. To deliver 20 g of protein, WPC 80 needs 26.3 g of powder at the moisture limit and WPI 90 needs 23.4 g. The difference is about 3 g of powder per serving, and it is the powder — with its lactose, fat and ash — that the rest of the formula has to carry.

Lactose and fat at the dose

What 20 g of protein carries · per serving, at the limits used in the grade comparison
Per 20 g proteinWPC 80WPI 90
Powder needed26.3 g23.4 g
Protein, as-is20.0 g20.0 g
Lactose, at the limit1.31 g0.23 g
Fat, at the limit1.58 g0.23 g
Ash, at the limit1.05 gProcess-dependent

Lactose is a reducing sugar, which matters beyond the carbohydrate figure. In a bar with humectants, or in a drink that meets heat, the lactose and the lysine in the protein are the two partners in the Maillard reaction that browns the product and lowers the available lysine. Cutting the lactose by a factor of five does not stop browning, but it removes most of the substrate.

Lactose is also not the allergen. Milk protein is. A WPI 90 with 1% lactose still contains milk protein and still carries the milk declaration, so the difference between the grades is a composition difference, not an allergen-free option. The compliance page covers the declaration both grades share.

What changes in the glass and on the line

In water, WPC 80 gives an opaque, milky dispersion that foams readily when mixed or pumped. WPI 90 gives a clearer solution with less foam. Neither is a defect; they are different ingredients, and a clear ready-to-drink product is built around the isolate for that reason.

Acid systems sharpen the difference. Whey proteins are least soluble near pH 4.5–5.0, and a concentrate at that pH is hazy and can sediment, while an isolate holds a clearer solution. A neutral or mildly acidic shake can use either grade, and the choice then comes back to lactose and fat rather than clarity.

In a bar, the concentrate's fat and lactose are part of the matrix: they carry flavour and soften the texture. The isolate brings more protein per gram of powder and less of everything else. Both can be agglomerated or instantized, which changes how the powder wets and how much dust it makes on a filling line but not what the label declares.

How the two are declared

In the EU, the ingredient list names the grade and emphasises the allergen: “whey protein concentrate (milk)” or “whey protein isolate (milk)”, with milk in bold or capitals as Regulation (EU) No 1169/2011 requires. In the US, the same names appear in the ingredient statement and the FALCPA declaration follows, either as “Contains: milk” or in a parenthetical.

“Whey protein” alone is a family name. A label that names a grade in the product name and a different grade in the ingredient list has a problem that no certificate fixes, and a supplement that declares “whey protein” without a grade has left the buyer to guess which one it is.

What the regulation does not change

Both grades are ordinary food ingredients in the EU, the US and the UK, and neither needs approval or a notification. Neither is a novel food, and neither sits in a different regulatory category from the other. The contaminant limits apply to the finished product as sold, not to the grade, so moving from concentrate to isolate does not change the limit that has to be met.

Protein claims work the same way for both. In the EU, “source of protein” requires protein to supply at least 12% of the energy value and “high protein” at least 20%; in the US, “good source” means 10–19% of the Daily Value and “high” at least 20%. The same 20 g of protein can be “high protein” in a 200 kcal drink and only “source of protein” in a 500 kcal one, whichever grade supplied it. The NRV glossary entry sets out the reference values behind those percentages.

When to choose each

Choose WPC 80 when the product is opaque, when the fat and lactose help the matrix, when a bar or a powder blend can carry 26 g of powder per serving, and when the specification's lactose ceiling of 5% is inside what the formula allows. Choose WPI 90 when the drink has to be clear, when the lactose ceiling is below what a concentrate can hold, when the serving cannot carry the extra 3 g of powder, or when the browning risk in a warm or high-moisture matrix has to be reduced.

Neither choice is settled by the protein percentage. It is settled by the dose, the matrix and the label, and then written into the specification as a grade, a lactose limit and a particle size. The grade comparison sets out the wider grade logic, the COA page covers the tests behind the numbers, and the product page carries the catalogue specification for WPC 80.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation