What the COA for rice protein peptides actually contains
The certificate for a rice protein peptide lot reports appearance, identification against a rice protein reference, protein by Kjeldahl with the nitrogen factor printed beside it, peptide content by size-exclusion HPLC, moisture, ash, the heavy-metal panel, microbiology and particle size. Two of those lines explain little on their own: protein is arithmetic done on nitrogen, and peptide content is a size distribution read from a chromatogram. The first table carries the catalog limits; the certificate speaks for one pack.
A rice peptide certificate is only complete when the protein figure carries its nitrogen factor and basis and the peptide figure carries its chromatographic cut-off and denominator.
Reading the sheet in order
Ask three questions of every row: what was measured, how, and against which limit. A row that says only “conforms” leaves a verdict without evidence. Two rows carry more weight: the protein row, because it is calculated from nitrogen, and the peptide row, because it depends on the method.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | Off-white to cream powder |
| Identification | Amino acid profile against a rice protein reference | Protein profile conform |
| Protein | Kjeldahl, N × 5.95, dry basis | ≥80.0% |
| Peptide content | SEC-HPLC, cut-off stated | ≥70.0% |
| Moisture | Gravimetric, vacuum oven | ≤7.0% |
| Ash | Gravimetric, muffle furnace | ≤3.0% |
The ash row is not housekeeping here. Hydrolysis is stopped or neutralised with a base, and the salt that remains reports as ash. The 3.0% ceiling keeps a peptide powder from carrying a large neutralisation load, and it is the first line to read when a peptide figure is high but the powder tastes salty.
Two calculations, two bases
Protein here is nitrogen multiplied by 5.95, the cereal factor, on the dry basis. The number is not a direct protein measurement: the laboratory measures nitrogen and applies the factor. The general labelling factor of 6.25 gives a different figure for the same nitrogen. A lot at 80.0% by 5.95 holds about 13.4% nitrogen, which reads 84.0% under 6.25. Both figures can be true; only one belongs on the certificate you agreed.
The dry basis is the other half of that statement. At the 7.0% moisture ceiling, 80.0% on the dry basis is about 74.4% on the powder as weighed. A buyer who compares that as-is figure with a dry-basis limit will reject a lot that conforms, and a supplier who presents the dry figure as if it were as-is is overstating the powder. The factor and the basis belong inside the protein row; a footnote does not carry them.
Peptide content is a different measurement. SEC-HPLC separates the soluble fraction by size and reports the share below a stated cut-off, usually somewhere between 5 and 10 kDa. The cut-off and the denominator both matter. A peptide figure expressed on the protein and one expressed on the powder differ by the protein content: at 80.0% protein, 70.0% on the protein is 56.0% on the powder. The certificate should name the denominator, and the specification should fix the method with it.
The two lines come from different instruments and do not have to add up: nitrogen counts free amino acids, which a peptide cut-off may exclude.
Release limit versus batch result
Keep parameter, method, limit and result in separate columns; a result column filled with the specification range is a copy of the gate. The table shows the shape it should take.
| Parameter | Limit | What the result reads |
|---|---|---|
| Protein | ≥80.0% with factor and basis | The measured figure, with the factor and basis repeated |
| Peptide content | ≥70.0% by SEC-HPLC | The percentage, the cut-off and the denominator |
| Moisture and ash | ≤7.0% and ≤3.0% | Measured percentages, read together with the protein |
| Heavy metals | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg | A figure for each element, inorganic arsenic included |
| Microbiology | A plate count plus absence tests | The count and the absence result for the lot |
| Particle size | ≥95% through 80 mesh | The sieve result, as a percentage passing |
Arsenic earns its own line rather than a place in a combined total. Rice takes inorganic arsenic from the paddy soil, and the bran fraction carries more than the polished grain. A certificate that reports one combined metal total hides the element this crop is most likely to carry. Microbiology is evidenced the same way: a count plus an absence statement, not the word “pass”.
What moves between batches
The rice source moves the specification before the enzyme does. Brown rice carries bran residues that raise ash, fiber and arsenic; white rice gives a paler, lower-ash powder; broken rice is a milling stream whose quality follows its own record. A change of rice supply can move the ash and the arsenic result without any change in the hydrolysis line.
Hydrolysis moves the peptide distribution. Enzyme dose, temperature and time decide where the curve sits; a longer hold pushes more of the protein below the cut-off, raises the free amino acid fraction and shifts the taste. The peptide result is a process fingerprint, not a fixed property of the source.
Neutralisation and drying move the rest. The base used to stop the enzyme leaves salt, which reports as ash; the dryer moves moisture, colour and bulk density; the sieve moves the 80 mesh figure. None of those changes the protein, and all of them appear on the certificate. Read the direction across lots — peptide drifting toward its floor, ash climbing, moisture creeping up — rather than one result near an edge, and make sure the lot code follows the pouch, the drum and the sample held back.
When to commission an outside test
Commission an independent laboratory for a new rice source, a first shipment into a regulated market, a peptide claim the supplier's certificate does not demonstrate, or a disputed result. The aim is to answer what the sheet leaves open, not to reproduce the sheet. The panel is Kjeldahl with Dumas as a cross-check, the full amino acid profile, SEC-HPLC with the cut-off named, moisture and ash, ICP-MS with inorganic arsenic reported separately, and microbiology.
Add a melamine and urea screen if the nitrogen will not reconcile with the amino acids, and a soy or wheat ELISA if the line is shared. Ask for the detection limit beside every screen; “not detected” without a limit describes the method, not the powder. Hold the tested powder beside the retained sample.
How two offers should be compared
Set six lines side by side: rice source and process; nitrogen factor and basis; protein and peptide figures with the cut-off and the denominator; moisture and ash; inorganic arsenic and cadmium; mesh and pack. Two quotations that agree on protein but differ on the peptide method or the factor are not describing the same powder.
The catalog specification is on the rice protein peptides page. The tests that separate a peptide from a diluted isolate are on the identity page; the intact isolate is compared on the level-four page; the separation is described in the HPLC method note; release is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation