06 Identity & adulteration

How we show a rice peptide lot is what it says

Technical document 06 · Reviewed 2026-11-20 · Rice Protein Peptides

On this page
  1. The five identity layers
  2. The ratios that carry the check
  3. What diffraction can and cannot show
  4. What adulteration looks like
  5. What the identity clause should say
  6. Five questions for the supplier

Rice protein peptides have no CAS number and no single molecular weight, so a lot is what the measurements say it is. Five have to agree: the rice source and the hydrolysis record are named; the nitrogen arithmetic backs the protein claim; the size-exclusion curve backs the peptide claim; the amino acid pattern is consistent with rice; and ash and moisture account for the rest of the mass. A peptide figure alone is weak evidence, because the method and the cut-off can be chosen to produce it.

In one line

Identity for a hydrolysate is a set of agreeing measurements, because the material has no CAS number and no single molecular weight to check against.

The five identity layers

A certificate can carry the right name and still prove very little. Each layer below answers a different question, and a supplier who stops at the first has shown the paperwork rather than the powder.

Five layers of rice peptide identity
LayerQuestion it answersEvidenceWhat it establishes
DocumentAre the source and the process named?Rice source, enzyme, process recordPaperwork only
NitrogenDoes the nitrogen support the protein claim?Kjeldahl, N × 5.95, dry basisNitrogen, not protein
PeptideHow much sits below the cut-off?SEC-HPLC with the cut-off statedA size distribution, not a species
SpeciesIs the protein rice?Amino acid profile against a rice referenceA rice-consistent pattern
BalanceIs the powder diluted or salted?Ash, moisture, free amino acidsConsistency of the numbers

The third layer is the one that separates a peptide from an isolate, and it is also the one most easily quoted without a method. The fourth layer is the only one that speaks to the source; a peptide figure says nothing about which plant the protein came from.

The ratios that carry the check

The first is peptide against protein. At the catalog limits, 70.0% peptide and 80.0% protein on the powder give a ratio of 0.875, and the two numbers must satisfy the same denominator. A peptide figure above the protein figure means the two sit on different bases or one is wrong, and the chromatogram deserves a look before the lot is booked in. At 80.0% protein, 70.0% taken on the protein is 56.0% when taken on the powder, so the same words describe two different powders.

The second is protein against ash. At the protein floor with ash at its ceiling the ratio is about 26.7:1. A lot at the same protein with a much lower ratio is carrying neutralisation salt or a carrier, and the taste agrees with the ash. A much higher ratio alongside a high protein figure suggests a washed base. Neither ratio releases a lot, but both can be read off a certificate that already prints the two lines.

The third check is the factor. The same nitrogen reads differently under 5.95 and 6.25 — about four points apart at this protein level — so two certificates can disagree without either laboratory being wrong. Ask which factor each supplier applied before the two are compared.

What diffraction can and cannot show

A spray-dried peptide is amorphous, so its diffraction pattern is a broad halo rather than a set of sharp reflections. That makes XRD a useful screen for a crystalline adulterant — salt from neutralisation, a mineral filler, a sugar alcohol — and a poor identity test for the peptide itself. A sharp pattern in a powder that should be amorphous is a question, not an answer.

The halo can be compared with a reference pattern, but no halo is a fingerprint of rice. The species question calls for the amino acid profile and, if the DNA has survived the process, a rice-specific PCR. A line reading only “XRD conforms” establishes an amorphous powder; it says nothing about the species.

What adulteration looks like

Rice peptide substitutions and what they leave behind
SubstituteEffect on the powderWarning signCheck
Rice flour or starchAdds starch and water-binding solidsProtein and peptide fall, starch risesStarch, iodine, mass balance
Soy or wheat proteinRaises protein and lysine; adds glutenLysine ratio up; gluten ELISA positiveAmino acid profile, ELISA, PCR
Free amino acidsLifts nitrogen and flavour without peptideFree amino acid fraction highFree amino acid panel, SEC
Neutralisation saltRaises ash; salty tasteAsh above 3.0%Ash, sodium by ICP-OES
Nitrogen spikingLifts the nitrogen figure without adding proteinNitrogen out of step with the profileLC-MS/MS screen, nitrogen balance
WaterRaises moisture; cakingMoisture above 7.0%Moisture, loss on drying

Appearance is the weakest of the signals. Off-white to cream covers a wide range, and a bleached powder sits inside it. The amino acid pattern, the ash figure and the peptide distribution, read with its method, are the ones to weigh.

What the identity clause should say

  • “Hydrolysed rice protein, with the rice source named and the enzyme recorded.”
  • “Protein ≥80.0% by Kjeldahl, N × 5.95, dry basis; factor and basis on the certificate.”
  • “Peptide content ≥70.0% by SEC-HPLC, with the cut-off and the denominator stated.”
  • “Amino acid pattern checked against a rice reference, with lysine and glutamic acid reported.”
  • “Moisture ≤7.0%; ash ≤3.0%; no carrier unless declared.”
  • “Inorganic arsenic and cadmium reported separately from the metal total.”

Five questions for the supplier

  1. Which rice source was hydrolysed, and which enzyme was used?
  2. Which SEC cut-off and which denominator produced the peptide figure?
  3. What ash, moisture and free amino acid figures accompany the peptide result?
  4. What is the inorganic arsenic result, and was it measured separately?
  5. If a result is challenged, will you re-test the retained sample with us?

An identity file can be built from five answers like these; a single peptide percentage cannot. The catalog specification sits on the product hub; the COA page shows which certificate line carries each figure; the grades page compares the peptide with the intact isolate; the level-four comparison works through dispersion and the label; the methods library covers the separation and the detection limits.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation