01 COA & batch testing

What the COA for porcine collagen peptides actually contains

Technical document 01 · Reviewed 2026-11-20 · Porcine Collagen Peptides

On this page
  1. The parameters on the sheet
  2. The factor and the basis behind the protein figure
  3. Release limit versus batch result
  4. What moves between batches
  5. When an outside laboratory earns its fee
  6. Six lines to compare between suppliers

The porcine collagen certificate has to settle three things that cannot be seen in the powder: how the protein figure was calculated, how much of the material is actually peptide, and which porcine tissue the lot came from. The catalogue limits are fixed; the batch COA shows where the lot landed. A sheet that reports only a protein percentage leaves the other two questions open.

In one line

A protein figure calculated with N × 5.55 and a peptide figure measured by SEC answer different questions, and both are needed before a porcine collagen lot can be released.

The parameters on the sheet

The release sheet has nine lines, and they fall into three groups: what the powder is, how much peptide it contains, and what must be absent. The table records the catalogue limits for this product; it is not a lot result.

COA parameters · porcine collagen peptides, catalogue specification
ParameterMethodRelease limit
AppearanceVisualOff-white to pale yellow powder
ProteinKjeldahl, N × 5.55≥90.0%
Peptide contentSEC-HPLC≥80.0%
Molecular weightSEC-HPLC≥80% below 3,000 Da
Loss on dryingGravimetric≤7.0%
AshGravimetric, furnace≤5.0%
Heavy metals (Pb, As, Cd, Hg)ICP-MS, reported element by elementPb ≤3 mg/kg; As ≤2 mg/kg; Cd ≤1 mg/kg; Hg ≤0.1 mg/kg
MicrobiologyAerobic plate count; absence tests as listedAPC ≤1,000 cfu/g; yeast/mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% passes 80 mesh

Two of the lines are words rather than numbers. The species and the tissue belong on the certificate because CAS 9007-34-5 covers collagen from any animal, and a specification that stops at the CAS number has not told the buyer what the drum contains.

The factor and the basis behind the protein figure

Kjeldahl reports nitrogen, not protein. The laboratory converts the nitrogen with a factor, and collagen takes 5.55 because its nitrogen content is close to 18%. The 6.25 factor used for many foods assumes 16% nitrogen and would turn the same titration into a figure roughly 12.6% higher. A 90.0% collagen result becomes about 101% under the general factor; nothing in the powder has changed.

There is a second convention to pin down. The 90.0% limit can be read on the powder as received or after drying, and the certificate has to say which. With loss on drying at the 7.0% ceiling, 90.0% on the dried basis equals about 83.7% as-is. Two compliant certificates can therefore show different percentages for the same material, and a buyer comparing one with the other will draw the wrong conclusion unless the basis is printed.

Nitrogen also arrives from non-protein sources. Urea, ammonium salts and other nitrogen compounds lift the Kjeldahl figure without adding collagen, which is why the peptide result belongs beside it rather than in a separate section.

Release limit versus batch result

A limit is a boundary; a result is a measurement. The certificate is useful only when the two are separated, the method is named, and the result is a number rather than the word “conforms”.

The peptide content and the molecular-weight distribution are not the same line. The first measures how much of the powder is peptide rather than free amino acids or other solids; the second measures how far the hydrolysis has gone. A lot can reach 80.0% peptide and still carry a high-molecular-weight tail, and the tail matters for dissolution and for the mouthfeel of a drink. Ask for the measured fractions, not only the cut-off.

Ash is a ceiling of 5.0% for this product. Skin-derived collagen normally sits well below it, so a result near the ceiling points to the raw material or the washing step and deserves a question before the lot is accepted.

What moves between batches

Lot-to-lot movement starts upstream. Porcine skin reaches the plant wet and fatty, and its fat, colour and microbial load depend on the animal, the chill and the delay before processing. Fat left in the material becomes an odour; colour left uncontrolled produces a pale-yellow lot next to an off-white one.

The hydrolysis then sets the curve. Enzyme dose, temperature and time decide how much of the collagen falls below 3,000 Da; filtration and concentration decide how much of that fine fraction reaches the dryer. The dryer fixes moisture, colour and particle size, and the 80 mesh result can shift with a new mill or sieve while the chemistry is unchanged.

Appearance is the least numerical line and often the first warning. A dull or darker powder can follow a longer heat exposure or a browning reaction with a reducing sugar, even when the assay passes. Keep the retained sample and the process record before rejecting a lot on colour, and confirm that the certificate's lot code matches the pack.

When an outside laboratory earns its fee

An outside laboratory is worth paying when the source is new, when a regulated market receives its first shipment, when the certificate does not support a species claim, or when a result is contested. The panel should close the open question rather than reproduce the whole sheet: protein with its factor and basis, the SEC curve, hydroxyproline as a collagen marker, a PCR on the raw tissue where the animal is in doubt, ICP-MS for the metals and the micro count.

Hydroxyproline is not on the catalogue limit list, but it is the most direct chemical evidence that the protein is collagen. Read against the protein figure, it catches a powder that reaches the nitrogen limit with a protein that is not collagen. It cannot name the animal, because porcine, bovine and fish type I collagens all contain it.

Every screen needs a detection limit. A “not detected” entry without one describes the method's sensitivity, not the lot, and a PCR that fails on a hydrolysate may reflect degraded DNA rather than a different source.

Six lines to compare between suppliers

Six lines make a supplier comparison: species and tissue; protein factor and basis; peptide content plus SEC distribution; moisture, ash and mesh; metals and microbiology; and the source documents, including the porcine declaration and the religious-use statement. A quotation that matches on protein but differs on the other five is a different material.

The certificate also has to connect to the batch. The plant, the raw batch, the hydrolysis and drying record and the retained sample are what let a buyer trace a drum backwards; a correct sheet can still belong to another lot.

The catalogue range is on the porcine collagen peptides product page. The tests that support the species claim are on the identity page; the source and label questions are on the compliance page; the chromatographic and nitrogen methods are described in the methods section; the quality page describes how a lot is released.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation