02 Grade comparison

Peanut protein peptides: which grade to specify

Technical document 02 · Reviewed 2026-11-19 · Peanut Protein Peptides

On this page
  1. Why the grade is a hydrolysis decision
  2. The catalog grade and the axes that can change
  3. Colour, solubility, flow and taste
  4. Dose arithmetic and the label
  5. What to write into the specification
  6. When a different legume protein is the better fit

Peanut protein peptides are specified on two numbers and one physical form: protein, peptide content and particle size. The catalog grade is ≥80.0% protein by Kjeldahl, ≥70.0% peptide by HPLC, ≤5.0% ash, ≤7.0% moisture and ≥95% through 80 mesh. A different grade moves one of those lines; it does not change the source, and it does not remove the peanut allergen.

In one line

The peanut peptide grade is set by the protein figure, the peptide figure and the mesh; the source stays peanut, so the allergen declaration stays with every grade.

Why the grade is a hydrolysis decision

The grade exists because hydrolysis is adjustable. Enzyme choice, dose, time, pH and temperature set how far the peanut protein is broken down, and that moves the peptide content, the bitterness, the salt load and the colour. The buyer is not choosing a flavour; the buyer is choosing a degree of hydrolysis and a specification to match it.

Protein and peptide answer different questions. Protein by Kjeldahl counts the nitrogen that the factor converts to protein, including peptides and free amino acids. Peptide by HPLC counts the fraction the method defines, usually below a stated molecular-weight cut-off. A high protein figure with a low peptide figure is closer to an intact peanut protein; a high peptide figure with a low protein figure is arithmetically limited, because the peptides are part of the protein.

The source is fixed. Every grade is peanut-derived, so every grade carries the peanut allergen statement. A finer mesh, a higher peptide figure or a granulated form does not make the material allergen-free.

The catalog grade and the axes that can change

Peanut protein peptide grade axes
ParameterCatalog gradeWhat can be agreed
Protein≥80.0% by KjeldahlA higher minimum, with the factor and basis named
Peptide≥70.0% by HPLCA higher minimum, with the HPLC cut-off named
Ash≤5.0%A lower ceiling for a low-salt process
Moisture≤7.0%A lower ceiling for a hygroscopic powder
Particle size≥95% through 80 meshGranulated, or a different mesh
FormPowder, 80 meshGranulated on request
Peanut allergenDeclaredDeclared; not removed by grade

The table is a set of axes, not a list of stock grades. Each axis is agreed before the quotation, and two axes can conflict: a higher peptide figure usually needs more hydrolysis, and a process that adjusts pH more leaves more salt, which pushes ash up. A specification that asks for a higher peptide and a lower ash has to be tested, not assumed.

The catalog grade is the starting point. A granulated form changes flow and dust, not the chemistry; a dilution with a carrier changes the label and the assay per gram; a higher protein minimum is a different specification, not a sorting step.

Colour, solubility, flow and taste

The catalog powder is off-white to light tan and free-flowing at 80 mesh. The colour is a range, not a fixed point; hydrolysis and drying move it, and a darker tan can be a Maillard signal rather than a different grade.

The powder dissolves in water; the solution is clear to slightly turbid. There is a limit to how much will dissolve, and pH, concentration and peptide size all affect clarity. A turbid solution is not automatically a failed lot. For a beverage, test clarity at the process pH and after the heat step.

The powder is hygroscopic at 80 mesh because the surface area is high. It can cake in an open pouch, and granulation can improve flow and reduce dust while slowing dissolution. Bulk density and flow are not catalog lines; ask for them if the fill weight or the filling line depends on them.

Taste follows the degree of hydrolysis. Peanut notes are part of the material, and a higher peptide figure can bring bitterness. A capsule hides the taste; a powder blend or a drink does not.

Dose arithmetic and the label

A 500 mg capsule of the catalog grade carries about 400 mg protein and about 350 mg peptide at the minima; the peptide is part of the protein, not an additional 350 mg. Two capsules carry about 800 mg protein from 1 g of powder. These are arithmetic, not a recommended dose.

A 5 g stick pack at 80% protein carries about 4 g protein; a 10 g serving carries about 8 g. The label declares the protein and the peanut source; the peptide figure is a specification line, not a nutrition claim.

The protein claim is calculated on the finished product. In the EU, “source of protein” is 12% of the energy from protein and “high protein” is 20%; in the US, “good source” is 10% of the daily value and “excellent source” is 20%. The brand's regulatory reviewer signs off that claim for the market.

The dosage form also sets the grade question: a tablet needs flow and compression, a capsule needs a fill weight, and a powder blend needs dispersion. Granulation can help the first two and hurt the third.

What to write into the specification

  • “Peanut protein peptides (peanut); source and allergen statement attached.”
  • “Protein ≥80.0% by Kjeldahl, factor 5.46, basis stated.”
  • “Peptide ≥70.0% by HPLC with the cut-off and integration range.”
  • “Ash ≤5.0%; moisture ≤7.0%; particle size ≥95% through 80 mesh.”
  • “Aflatoxin B1 and total aflatoxin limits, with the sampling plan.”
  • “No undeclared carrier, diluent or added amino acid.”
  • “Granulation or a different mesh only as an agreed revision.”

A purchase order that says “peanut peptide” without the protein and peptide methods is not a specification. The allergen statement belongs in the same document, because it is the one line that no grade can change.

When a different legume protein is the better fit

If the brief cannot carry a peanut allergen, the grade is the wrong material, not the wrong mesh. Soy protein isolate and pea protein isolate are the other legume options, and each brings its own protein level, taste and allergen position. Soy is a major allergen; pea is a legume with a different profile, not an allergen-free promise.

If the target is the highest protein per gram, a soy peptide or isolate can be higher: the soy peptide grade is ≥90% protein and ≥80% peptide, while the peanut grade is ≥80% and ≥70%. That difference is a reason to compare the materials, not to relabel one as the other.

If the target is a neutral taste, peanut's nutty notes may not fit a delicate drink; if the target is a clear solution at low pH, the peptide may need a trial. The peanut versus soy comparison takes the decision further. The catalog specification sits on the product hub; the HPLC methods are described in the methods section; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation