06 Identity & adulteration

How we prove a hemp protein lot is hemp seed protein

Technical document 06 · Reviewed 2026-11-20 · Hemp Protein

On this page
  1. Four checks on the powder
  2. The nitrogen factor and the amino acid ratios
  3. What X-ray diffraction can and cannot show
  4. How adulteration shows up
  5. Identity lines for the specification
  6. Questions to put to the supplier

A hemp protein lot is the named material when four lines agree: the protein figure carries the hemp nitrogen factor and dry basis, the amino acid profile has the shape of hemp seed protein, the source DNA is Cannabis sativa, and the mass balance around fat, fibre, ash and moisture adds up. The protein percentage alone cannot separate hemp protein from pea, soy or a nitrogen-spiked blend.

In one line

A hemp protein lot is proved by four agreeing measurements: the nitrogen factor, the amino acid profile, the source DNA and the mass balance around fat, fibre and ash.

Four checks on the powder

Naming the right material on paper does not prove that the powder is that material. The four checks below test the powder itself, and each needs its own evidence. An answer that stops at the name is a paperwork answer.

Four checks on a hemp protein lot
CheckQuestionTestWhat it establishes
Protein basisIs the factor and dry basis stated?Kjeldahl, N × 5.7, dry basisThe protein figure
Amino acid profileDoes the protein look like hemp?Amino acid profile and SDS-PAGEThe protein family
Source DNAIs the plant Cannabis sativa?PCR or DNA barcodingThe species
Mass balanceIs the powder diluted?Protein, fat, fibre, ash, moistureConsistency of the numbers

DNA survives processing unevenly, so a PCR result needs a positive control and a sample that still amplifies. A negative PCR on a heavily processed powder is not proof that hemp is absent.

The nitrogen factor and the amino acid ratios

The protein figure is nitrogen multiplied by a factor. Hemp is specified here at N × 5.7; the general food factor is N × 6.25. The same nitrogen multiplied by 6.25 reports about 9.6% more protein, so a 50.0% hemp result under N × 5.7 becomes 54.8% under N × 6.25. The factor is a convention, not a purity measure, and it must be on the certificate and the quotation.

The amino acid profile is the second ratio. Hemp seed protein is high in arginine and low in lysine; a published hemp protein isolate reports about 15 g arginine and 2.5 g lysine per 100 g protein, with tryptophan also low. Pea protein runs the other way: high lysine, low methionine and cysteine. A blend moves the ratios toward the middle, and a nitrogen spike moves the crude protein without moving the amino acid sum.

Amino acid markers · hemp seed protein against pea protein
MarkerHemp seed proteinPea proteinWhat a shift means
Nitrogen factorN × 5.7 (catalogue)N × 6.25 (catalogue)A different factor changes the declared protein
ArginineHigh, about 15 g/100 g proteinLowerA drop suggests dilution or another source
LysineLow, about 2.5 g/100 g proteinHighA rise suggests pea or another legume
Methionine + cysteineModerate, about 5.5 g/100 g proteinLowA rise suggests a cereal or a blend
TryptophanLow in some isolatesModerateA very low value fits hemp

The table is a fingerprint, not a specification. The absolute values move with variety, dehulling and processing, so the laboratory should compare the lot with a reference profile and with the declared source, not with a single number copied from a paper.

What X-ray diffraction can and cannot show

XRD tests the solid state: whether the powder is crystalline and whether the pattern matches a reference. A protein powder is largely amorphous, so the expected pattern is a broad halo rather than sharp peaks. A crystalline spike can point to an adulterant such as lactose, melamine, urea or a salt, or to a crystalline fibre fraction. It does not measure protein and it does not distinguish hemp from pea.

Before accepting a “match” statement, request the reference diffractogram and the detection limit. On a disputed lot, XRD, the amino acid profile and the DNA test together outweigh any single result. Hemp protein does not need XRD at release; a “conforms” line without the pattern adds little.

How adulteration shows up

The likely substitutions are other seed proteins, a fibre or starch filler, a nitrogen source that is not protein, or a leaf and resin fraction that changes the cannabinoid profile. Each has a different signal. The table below is a starting point, not a complete screen.

Common hemp protein substitutions and the signals
SubstituteEffectSignalTest
Pea, soy, rice or wheat proteinRaises the protein figure; changes the amino acid patternLysine or methionine shift; foreign bands on SDS-PAGEAmino acid profile, SDS-PAGE, PCR
Maltodextrin or starchDilutes protein; adds carbohydrateProtein and ash low; crystalline or starch peaksMass balance, XRD, microscopy
Fibre or hull powderRaises fibre; lowers proteinFibre high; colour greener; ash upFibre, ash, microscopy
Melamine or ureaRaises Kjeldahl nitrogen without proteinAmino acid sum far below crude proteinAmino acid profile, HPLC, NMR
Leaf or resin fractionAdds cannabinoids and chlorophyllTHC or THCA above the limit; colour darkLC-MS/MS, THC statement
ColourantMatches the green tintColour without a chlorophyll spectrumUV-Vis, HPLC

Appearance is the weakest evidence. Hemp protein ranges from off-white to light tan with a green cast, and a dye can reproduce it. What carries weight is the amino acid ratio, the DNA result, the THC profile and the mass balance. Appearance and protein alone leave the obvious substitution untested.

Identity lines for the specification

  • “Hemp seed protein, Cannabis sativa L., from hulled, defatted seed; 50% concentrate.”
  • “Protein ≥50.0% on a dry basis by Kjeldahl, N × 5.7.”
  • “Identification: protein profile conform by SDS-PAGE and amino acid profile.”
  • “Fat ≤10.0%; total dietary fibre ≤10.0%; ash ≤6.0%; moisture ≤7.0%.”
  • “THC and THCA within the destination limit; cadmium and the heavy-metal panel as listed.”
  • “No foreign protein, no added nitrogen source and no leaf or resin fraction.”
  • “Cannabis sativa specific PCR on request; retained sample per lot.”

Questions to put to the supplier

  1. Which plant part and variety is this lot, and was the seed hulled and defatted?
  2. What protein factor and basis are on the certificate, and what is the as-is figure?
  3. Will you send the amino acid profile and the SDS-PAGE, not just the protein percentage?
  4. What are the THC, THCA and cadmium results for this lot, and which methods were used?
  5. Would you agree to a joint re-test of the retained sample if the lot were disputed?

Five answers of that kind make an identity file; a protein percentage alone does not. The product hub carries the catalogue specification; the COA page maps each figure on the lot certificate; the grades page sets out the powder grades; the compliance page covers the THC limits; the XRD method note explains the solid-state test.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation