01 COA & batch testing

What the COA for hemp protein actually contains

Technical document 01 · Reviewed 2026-11-20 · Hemp Protein

On this page
  1. Reading the certificate as a test report
  2. Dry basis, moisture and the protein factor
  3. Release limit and batch result
  4. What changes from lot to lot
  5. When an outside test is worth ordering
  6. Comparing two suppliers

A hemp protein certificate has to be read from the protein line outward. The figure means nothing without its nitrogen factor and dry basis, and the moisture, fat, fibre and ash lines explain the rest of the powder. The contaminant and microbiology results then decide release for the intended market.

In one line

A hemp protein certificate is only complete when the protein figure carries N × 5.7 and a dry basis, with moisture, fat and fibre beside it to explain the rest of the powder.

Reading the certificate as a test report

Hemp protein is a concentrate made from defatted hemp seed, so the certificate describes a mixture, not a single molecule. Fat, fibre, ash and moisture make the protein figure usable, and each row should carry the method and the limit beside the result. A certificate that reports only “protein 50%” has not said whether the powder is a lean concentrate or a partly defatted meal with a similar nitrogen count. The identity row matters too, because a protein profile can be satisfied by a different seed protein.

Identity and proximate limits · hemp protein, 50% grade
TestMethodLimit
AppearanceVisualOff-white to light tan powder
IdentificationProtein profile against reference (SDS-PAGE and amino acid profile)Conforms
ProteinKjeldahl, N × 5.7, dry basis≥50.0%
FatSolvent extraction≤10.0%
FibreTotal dietary fibre, enzymatic-gravimetric≤10.0%
AshGravimetric, muffle furnace≤6.0%
MoistureOven drying≤7.0%
Particle sizeSieve analysis≥95% through 80 mesh

The catalogue limits above are the specification. The batch certificate repeats them beside the measured result for the lot; a result column that repeats the limit has not reported a measurement.

Contaminant, microbiology and hemp-specific checks
ParameterMethodRelease limit or statement
Heavy metalsICP-MSPb max 3 · As max 2 · Cd max 1 · Hg max 0.1 mg/kg
MicrobiologyPlate count and absence testsAPC max 1,000 cfu/g; yeast and mould max 100 cfu/g; E. coli and Salmonella absent
THC and THCALC-MS/MSDestination limit; 3.0 mg/kg as Δ9-THC equivalents in the EU for seed-derived products

THC is not a catalogue line for this grade, but it is a lot statement for any hemp-derived food ingredient. In the EU the limit for processed seed products is 3.0 mg/kg as Δ9-THC equivalents, as of this review; a certificate that omits the THC result leaves the destination question open.

Dry basis, moisture and the protein factor

The protein result is reported on a dry basis. Nitrogen is measured on the powder as received, converted with the 5.7 factor, and then corrected for dry matter. At the catalogue moisture limit of 7.0%, a 50.0% dry-basis result is 46.5% as-is. A lot at 52.0% dry basis and 5.0% moisture would be 49.4% as-is. The dry-basis and as-is figures describe the same powder at different points, and only the as-is figure matches the weigh-up.

The factor is a convention, not a measure of protein quality. Hemp is specified here at N × 5.7; the general food factor is N × 6.25, and the same nitrogen reports about 9.6% more protein under it. A 50.0% hemp result becomes 54.8% under N × 6.25 without a gram of powder changing. A certificate that does not name the factor cannot be compared with another one.

Release limit and batch result

The limit defines pass or fail; the result is the value the laboratory measured. Each needs its own column, and the method has to sit next to it. The table below sets out what the result column should contain, not a set of batch figures.

What the result column should show
TestLimitResult
Protein≥50.0% dry basis, N × 5.7A measured percentage, with the factor and basis
Fat≤10.0%A measured percentage and the extraction method
Fibre≤10.0%A measured percentage and the fibre method
Ash≤6.0%A measured percentage
Moisture≤7.0%A measured percentage and the drying method
Heavy metalsPer elementA separate mg/kg figure for each metal
MicrobiologyCounts and absenceThe lot count and its absence statement
Particle size≥95% through 80 meshThe measured percentage through the sieve

Two method choices change the number more than the lot does. Fat by Soxhlet leaves bound lipid behind, while acid hydrolysis recovers more; crude fibre is not total dietary fibre, and the enzymatic-gravimetric method reads higher. State the method, or the limits are not comparable.

What changes from lot to lot

Hemp is a small-acreage crop, and the powder moves with the seed and the press. Variety, season and soil change the protein and the mineral load; dehulling changes the fibre, pressing changes the fat, and the mill changes the particle size. A lot at 50.5% protein with 9.5% fat and 9.5% fibre would be inside the limits but would be a different powder from one at 55% protein, 5% fat and 4% fibre. The limits do not describe the lot; the results do.

Appearance is the least quantitative line. Hemp protein carries chlorophyll, so the powder ranges from off-white to light tan with a green cast; pressing and storage move it. A darker batch is not automatically out of specification, but a colour shift with a rising peroxide value points to oxidation.

Watch the direction across lots rather than a single result at the edge: protein drifting down, fat drifting up, or fibre climbing as more hull travels with the meal. Certificate, pack and retained sample should all carry the same lot code.

When an outside test is worth ordering

An outside test is worth ordering for a new source, a first regulated-market shipment, an organic or non-GMO claim, a disputed protein figure, or an open THC or cadmium question. The panel is Kjeldahl protein with the factor and dry basis, an amino acid profile, fat, total dietary fibre, moisture, ash, ICP-MS metals, microbiology, and THC and THCA by LC-MS/MS.

Add a Cannabis sativa specific PCR or SDS-PAGE when the source is disputed, and a pesticide screen when the destination requires one. Each screen should come with its detection limit; a “not detected” result without one describes the method, not the powder.

Keep the chain of custody tight: test the retained sample, and put the lot number on the report. A dispute goes to a referee with the retained sample, the certificate and the specification, and a request for tests that tell hemp protein from another seed protein.

Comparing two suppliers

Put seven lines side by side: the plant part and variety, the grade, the protein factor and basis, the fat and fibre results, the THC and cadmium results, the contaminant panel, and the pack and lot code. Agreement on “50% protein” means little if the factor, the fat or the fibre still differ; those offers describe different powders.

The second layer is traceability: who manufactured the lot, whether the seed was hulled, how the oil was removed, and which mill finished the powder. The catalogue specification sits on the hemp protein product page; the grade comparison covers the options; the identity page covers the tests; methods covers the methods; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation