02 Grade comparison

Hemp protein 50%, 65% or isolate: choosing a grade

Technical document 02 · Reviewed 2026-11-20 · Hemp Protein

On this page
  1. Why hemp protein comes in grades
  2. The grades side by side
  3. Particle size, colour and flow
  4. Dose arithmetic and the serving
  5. Specification lines for a hemp grade
  6. When the 50% grade is the wrong choice

Hemp protein is sold as a family of powders, not one grade. The catalogue material is a 50% protein concentrate with fat and fibre caps; a higher-protein concentrate, an isolate and a granulated version are different specifications. The grade has to be chosen from the dosage form and the label, not from the protein number alone.

In one line

The grade is the protein floor plus the fat and fibre left beside it; the number on the front of the pack does not say which powder is inside.

Why hemp protein comes in grades

Hemp seed is about a quarter to a third protein, with oil and fibre making up most of the rest. The protein is separated by removing the oil and part of the hull, then milling the cake. How far that separation goes decides the grade: a seed powder, a concentrate, a higher-protein concentrate or an isolate.

The grade is a process endpoint, not a variety. The same seed can become a 50% concentrate or an 85% isolate depending on the extraction and drying route, and the two powders behave differently in a formula even when both are called hemp protein.

The grades side by side

Hemp protein grades and what each one carries
GradeProtein, dry basisFatFibreProcessTypical use
Full-fat seed powderAbout 25–30%25–35%20–30%Milling whole seedFlavour and texture; not a protein concentrate
50% concentrate (catalogue)≥50.0%≤10.0%≤10.0%Pressing, dehulling, millingPowder sticks, bars, blends
60–65% concentrate≥60.0%≤8.0%≤6.0%Further defatting and classificationHigher-protein bars, compact servings
85–90% isolate≥85.0%≤2.0%≤2.0%Alkaline extraction, precipitation, dryingHigh-protein powders and beverages

The first three rows are concentrates or seed powders; only the fourth is an isolate. The catalogue grade is the second row: a 50% concentrate with the fat and fibre caps in the product record. A 60–65% concentrate is a different purchase, and an isolate is a different process with a different ash and fibre profile. Values outside the catalogue row are typical published ranges, not limits we release against.

Particle size, colour and flow

The catalogue powder is ≥95% through 80 mesh. That fineness disperses well in a shaker but carries dust and wets slowly; granulation gives a coarser particle that flows and disperses faster at the same protein and fat limits. Milling and sieving set the particle size, so it can move with a new mill or screen while the chemistry stays the same.

Hemp protein is opaque and slightly grainy in water; it disperses rather than dissolves. Colour runs from off-white to light tan with a green cast from chlorophyll, and the flavour is earthy and green. Fat makes the powder more prone to oxidation and gives a heavier mouthfeel; fibre binds water and can thicken a bar or a drink. A granulated grade changes the flow, not the nutrition panel.

Dose arithmetic and the serving

Start from as-is protein, not the dry-basis figure. At 50.0% dry basis and 7.0% moisture, the powder is 46.5% protein as-is. A 20 g protein serving needs 43.0 g of powder; a 30 g scoop delivers 14.0 g. At 55.0% dry basis and 5.0% moisture the as-is figure is 52.3%, so 20 g of protein needs 38.3 g. At 88.0% dry basis and 5.0% moisture an isolate is 83.6% as-is, and 20 g needs 23.9 g.

The serving has to carry the rest: fat, fibre, ash and carbohydrate. A 30 g stick cannot hold 43 g of a 50% powder, so a 20 g protein claim from this grade needs a larger serving or a higher grade. The same arithmetic explains why a bar built on 50% hemp protein carries more fibre and fat per gram of protein than one built on an isolate. Neither is wrong; the label and the matrix have to agree.

Specification lines for a hemp grade

  • Source: Cannabis sativa L. seed, hulled and defatted; name the variety or supply region where known.
  • Grade: 50% concentrate, 80 mesh powder or granulated.
  • Protein: ≥50.0% on a dry basis by Kjeldahl, N × 5.7.
  • Fat ≤10.0%; total dietary fibre ≤10.0% with the method named; ash ≤6.0%; moisture ≤7.0%.
  • Identification: protein profile conform by SDS-PAGE and amino acid profile.
  • Heavy metals, microbiology and particle size as on the product record.
  • THC and THCA statement against the destination limit; allergen, GMO and origin statements.

When the 50% grade is the wrong choice

The 50% grade is the wrong choice when a single serving has to deliver 20 g or more of protein in a small pack, when the formula cannot carry 10% fat or 10% fibre, or when the powder has to be light in colour and mild in flavour. A higher-protein concentrate or an isolate reduces the non-protein load, but it is a different specification and a different process.

It is also the wrong choice when the protein claim is calculated on a tight energy budget: the fat and fibre in the concentrate add energy and mass that the claim has to absorb. The grade decision belongs before the nutrition panel is fixed, not after.

The numbers are published on the hemp protein product page. The certificate lines are on the COA page; the market and label rules are on the compliance page; the comparison with pea protein is on the level-four page; the method notes are at methods.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation