01 COA & batch testing

What the COA for eggshell membrane collagen contains

Technical document 01 · Reviewed 2026-11-20 · Eggshell Membrane Collagen

On this page
  1. The certificate as a test report
  2. What the protein and peptide figures are measured against
  3. Release limit versus batch result
  4. What moves between lots
  5. When to order an outside test
  6. What to compare between suppliers

Eggshell membrane collagen is a peptide hydrolysate with a mineral footnote, and its certificate has to show both. The protein figure and the SEC-HPLC distribution describe the hydrolysate; the ash and calcium results describe how much shell travelled with the membrane. The table below lists the catalogue gates for an 80 mesh lot, and the lot certificate records what the laboratory found against each one.

In one line

A membrane collagen certificate is read in three lines: the protein figure with its factor, the peptide distribution with its method, and the ash that shows how cleanly the membrane was separated from the shell.

The certificate as a test report

Begin with the parameter block. For each line, the certificate should show what was measured, how it was measured and the boundary the lot had to meet. A certificate that prints only “conforms” gives the reader a verdict without the working.

COA parameter list · eggshell membrane collagen, 80 mesh
ParameterMethodRelease limit
AppearanceVisualOff-white to pale yellow powder
ProteinKjeldahl, N × 5.55≥90.0%
Peptide contentSEC-HPLC≥80.0%
Molecular weightSEC-HPLC, calibration reported≥80% below 3,000 Da
Loss on dryingGravimetric≤7.0%
AshGravimetric, furnace≤5.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and enrichmentAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Source is a line on the specification as well as a fact about the lot. Egg membrane is an egg-derived material, and the certificate and the specification should say so. The identity page shows how that claim is supported.

What the protein and peptide figures are measured against

Kjeldahl reports nitrogen, and the number becomes protein only after a divisor is chosen. Collagen uses 5.55, a convention that assumes about 18% nitrogen; a general food protein uses 6.25, which assumes 16%. The same nitrogen result divided by the smaller figure gives a protein percentage roughly 13% higher, so a certificate that omits the factor is not comparable with one that names it.

Moisture determines the second half of the protein statement. A 90.0% figure on the dry basis becomes about 83.7% as-is when the loss on drying is 7.0%. Both numbers can be correct; a purchase order or label that mixes them is not.

SEC-HPLC produces two different statements. One is how much of the powder behaves as peptide; the other is how the peptide mass is spread across molecular weights. A lot can clear the 80% peptide gate and still contain a tail of larger molecules that clouds a drink. Read the curve, the column and the calibration, not just the pass line.

Ash is what remains after the organic fraction burns away. Calcium carbonate from the shell is the expected source in this material, so an ash result near the 5.0% ceiling points to shell carry-over. Calcium by ICP-OES tells you whether that is the cause; a second ash test does not.

Release limit versus batch result

A specification is a gate; a result is a measurement. The certificate should keep them in separate columns, because a result column copied from the specification says nothing about the lot.

What the result column should contain
ParameterRelease limitResult column
Protein≥90.0%, basis statedA measured percentage, with the factor and the basis
Peptide content≥80.0%The measured percentage and the SEC method
Molecular weight≥80% below 3,000 DaThe distribution, not only the cut-off
Ash≤5.0%A measured percentage; calcium if ash is high
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot

Microbiology needs a count and an absence statement; for an egg-derived powder, the absence of Salmonella carries the most weight. Metals need one figure per element. A single total hides which metal drove the number.

What moves between lots

Several physical steps move a lot. The membrane is peeled or washed off the shell at a breaking plant, and how much shell dust survives that step changes ash, calcium and colour. Hydrolysis time and temperature set the peptide curve. Drying sets moisture and colour; milling and sieving set the 80 mesh result.

Odour is a useful non-numeric signal. A membrane hydrolysate can smell faintly of egg or broth, and the note grows in a warm, damp store. A lot can pass protein while its odour has moved beyond what a flavoured drink can cover, so keep a retained sample and its storage history.

One result near a limit is less informative than a trend. Watch protein, ash and the high-molecular-weight tail across consecutive lots, and check that the lot code on the certificate matches the pack and the retained sample.

When to order an outside test

Use an outside laboratory when the supplier's certificate cannot close the question: a new membrane source, a first shipment to a regulated market, a disputed source claim or a contested result. A focused panel is protein with the factor, hydroxyproline, SEC-HPLC, egg-specific PCR, ICP-MS, microbiology and calcium or ash XRD.

Ask for the detection limit behind every “not detected” statement, and keep the sample identity intact. If a result is challenged, send the retained sample, the specification and the supplier's certificate to the referee, and ask for the discriminating tests rather than a second run of the same assay.

What to compare between suppliers

Compare specifications, not just protein percentages. Six lines expose most of the difference: protein with factor and basis; the SEC curve and its method; ash and calcium; membrane preparation and origin; the egg allergen statement and the enzyme; pack, lot code and micro results.

Traceability is the second layer. The file should name the manufacturing site, the membrane preparation, the hydrolysis conditions and the retained sample. The catalogue ranges are on the product page; the source evidence is on the identity page; the market file is on the compliance page; the SEC method sits in the methods library; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation