02 Grades & forms

Eggshell membrane collagen: peptide cut, mesh and ash

Technical document 02 · Reviewed 2026-11-20 · Eggshell Membrane Collagen

On this page
  1. Why a membrane collagen has grades at all
  2. The grade levers side by side
  3. Solubility, colour and flow
  4. Dose arithmetic and the label
  5. What to write into the specification
  6. When a grade is the wrong choice

Eggshell membrane collagen is sold as a hydrolysed peptide powder, and three numbers separate the grades that matter: the peptide cut, the mesh and the ash ceiling. The catalogue standard is ≥90.0% protein, ≥80.0% peptide with ≥80% of the distribution below 3,000 Da, ≥95% through 80 mesh and ash ≤5.0%. A granulated form, a tighter ash limit or a narrower peptide cut can be agreed, and each one changes flow, clarity or label arithmetic rather than the source.

In one line

The grade of an eggshell membrane collagen is set by three numbers — the peptide cut, the mesh and the ash — while the membrane source stays the same across all three.

Why a membrane collagen has grades at all

The raw material is a membrane, not a hide. It arrives as a thin, insoluble network that lines the inside of the eggshell, and the hydrolysis step turns that network into water-soluble peptides. How far the hydrolysis is taken decides the molecular-weight distribution; how the membrane is separated from the shell decides the ash; how the dried powder is milled or granulated decides the mesh and the flow.

Those are three separate levers, and a buyer usually cares about one at a time. A capsule line cares about flow and fill weight, a clear drink cares about haze and mouthfeel, and a label that declares a peptide content cares about the distribution curve. The grade conversation should start from the dosage form and the label, not from a generic “fine powder”. The product page carries the catalogue ranges that the grades are built from.

The grade levers side by side

Grade levers · hydrolysed eggshell membrane collagen
LeverCatalogue positionTighter optionWhat it moves
Protein≥90.0% (Kjeldahl, N × 5.55)Higher minimum on requestMass per declared milligram; mass balance
Peptide cut≥80.0% peptide; ≥80% below 3,000 DaA narrower distribution agreed on the curveSolubility, haze, mouthfeel, foam
Mesh≥95% through 80 meshGranulated on requestFlow, dust, blend uniformity
Ash≤5.0%Lower ceiling on requestShell carry-over, colour, mineral load

The table describes specification options, not a stock list. Each tighter option has to be written into the purchase order and confirmed on the certificate; a standard grade does not silently become a tighter one because the application would prefer it.

Solubility, colour and flow

The hydrolysate dissolves in water to a clear to slightly opalescent solution. Haze usually comes from the high-molecular-weight fraction, from a pH near the isoelectric point, or from undissolved granule; it is a reason to look at the distribution curve rather than to add more mixing. The solution foams when agitated, which matters on a filling line and in a stick pack that is shaken by the consumer.

Colour runs from off-white to pale yellow. A darker or greyer powder can point to shell carry-over, a hotter drying step or a Maillard reaction with residual reducing sugars; the protein figure can still pass. Odour follows the same pattern: a faint egg or broth note is normal for a membrane hydrolysate, and it strengthens with moisture and storage temperature.

Granulation improves flow and reduces dust, but it also slows dissolution and changes the particle-size line. A capsule or tablet line that values flow may prefer it; a powder blend that must dissolve quickly may not. The mesh figure is a finishing specification, so it can change without any change in the chemistry.

Dose arithmetic and the label

The label mass and the protein mass are not the same number. A formula that declares 500 mg of eggshell membrane collagen per serving weighs 500 mg of the powder. At the catalogue protein minimum that powder carries at least 450 mg of protein, before the loss on drying is counted. That is arithmetic, not a dose recommendation.

The peptide line is separate, and the specification has to say whether the 80.0% is expressed on the powder or on the protein. The two readings give different numbers: if the peptide minimum is on the protein, 400 mg of peptide needs about 556 mg of powder at the 90.0% protein figure; if it is on the powder, it needs 500 mg. A label that mixes the two bases is wrong before any analytical variation is counted.

If the label declares protein rather than the ingredient, the calculation runs the other way: the powder mass is the declared protein divided by the protein fraction. A 90.0% minimum means 500 mg of protein needs at least 556 mg of powder. The basis has to travel with the number: a 90.0% figure on the dry basis is about 83.7% as-is at the 7.0% moisture limit, so a label built on the dry-basis figure and a weigh-up built on the as-is powder will disagree by several percent.

What to write into the specification

  • “Hydrolysed eggshell membrane collagen, CAS 9007-34-5 (source-defined); source: eggshell membrane.”
  • “Protein ≥90.0% by Kjeldahl, N × 5.55, basis stated; loss on drying ≤7.0%.”
  • “Peptide content ≥80.0% by SEC-HPLC; ≥80% of the distribution below 3,000 Da, curve reported.”
  • “Ash ≤5.0%, with calcium reported beside the ash result.”
  • “Particle size ≥95% through 80 mesh; granulated on request.”
  • “Heavy metals, microbiology and egg allergen statement as on the COA page; hydrolysis enzyme and origin declared.”

The specification should be specific enough that a second laboratory could reproduce the release decision. The COA page lists the release tests, and the membrane versus collagen peptides page explains why the source belongs in the same document as the peptide cut.

When a grade is the wrong choice

A high-ash grade is the wrong choice for a clear beverage or a pale powder blend: the mineral load can add haze and colour even when the protein passes. A granulated grade is the wrong choice when the application needs rapid dissolution and the line has no high-shear step. A narrow peptide cut is unnecessary when the label makes no peptide claim and the dosage form is an opaque capsule.

The reverse error is just as common: buying a standard grade and writing a label that promises a specific peptide size or a low ash figure the certificate does not carry. The grade is part of the specification, and the label should not describe a grade that was not ordered.

If the formula needs a glycosaminoglycan story as well as collagen, that is a separate ingredient decision. Hyaluronic acid is specified on its own molecular-weight and assay lines; the small GAG fraction that comes with a membrane hydrolysate is not a substitute for it.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation