06 Identity & adulteration

How to prove a lot is casein phosphopeptides

Technical document 06 · Reviewed 2026-11-19 · Casein Phosphopeptides

On this page
  1. The four identity layers
  2. The calcium-to-phosphorus pair
  3. What XRD can and cannot show
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A casein phosphopeptide (CPP) lot is identified when four measurements agree: the peptide distribution shows the phosphopeptide fraction, the protein figure carries the right factor and basis, the calcium and phosphorus pair shows the mineral load, and the ash is consistent with it. The name on the certificate is the weakest layer; the calcium figure alone is the second weakest, because an added calcium salt also titrates.

In one line

A CPP lot is identified by four agreeing measurements: the peptide profile, the protein figure with its factor, the calcium and phosphorus pair, and the ash that shows the mineral load.

The four identity layers

No single line proves CPP. A protein figure can be met by casein, a calcium figure by a calcium salt, and a peptide figure by another hydrolysate. The layers below are separate questions, and each needs its own evidence.

Four layers of casein phosphopeptide identity
LayerQuestionTestWhat it proves
DocumentIs the material named and sourced?Name, source, lot, allergen statementPaperwork and traceability only
PeptideIs it the phosphopeptide fraction?HPLC peptide distribution; amino acid profileThe fraction, not the parent protein
MineralIs the calcium bound or added?Calcium by titration; phosphorus by ICP-OES; ashThe mineral load and its consistency
ProvenanceWas the process the stated one?Site, hydrolysis record, membrane step, retained sampleThat the lot matches the file

The first layer proves intent, not identity, because a document can describe a material that was never made. The other three are evidence, and they are read together.

The calcium-to-phosphorus pair

The phosphoserine clusters carry calcium, and the phosphate is part of the peptide. That makes calcium and phosphorus a pair: in the bound material they rise and fall together with the peptide load, while an added calcium salt raises calcium and ash without raising phosphorus.

The molar ratio is the check. Convert both figures to moles (calcium ÷ 40.08, phosphorus ÷ 30.97) and compare the ratio across lots and against the specification. A lot with calcium at the top of the 2.0–4.0% range and a phosphorus figure that has not moved is a lot with added calcium, not a lot with more phosphopeptide.

The ash is the third line. At 4.0% calcium the oxide alone is about 5.6% of the powder, and the phosphate adds to it; an ash figure near the 10.0% ceiling is consistent with a high mineral load, while a high calcium figure with a low ash is arithmetically odd and worth a question.

Phosphorus is not on the catalog specification. Ask for it when the phosphorylation is the reason for the purchase, when a new source is being qualified, or when the calcium figure is being used to argue that the material is CPP.

What XRD can and cannot show

Casein phosphopeptides are amorphous. A diffractogram shows a broad halo and no crystalline peaks, so XRD cannot identify the peptide or separate CPP from casein, a hydrolysate or a milk protein concentrate.

It can show a crystalline mineral phase. Calcium carbonate is crystalline, and a powder that shows calcite peaks has a mineral phase that the calcium figure alone would not distinguish from bound calcium. A calcium phosphate phase may be amorphous or crystalline depending on the process, so a clean diffractogram does not prove that no mineral was added.

Use XRD as a screen when the calcium figure is high and the phosphorus figure is low, not as a release test. Ask for the reference pattern and the detection limit before reading a “match” statement.

What adulteration looks like

Substitution routes · what gives them away
RouteMarkerTest
Non-protein nitrogen (melamine, urea)Protein high; amino acids lowKjeldahl plus amino acid profile; melamine and cyanuric acid screen
Casein or milk protein addedPeptide low for the protein figureHPLC peptide distribution
Other hydrolysate (plant, gelatin)Amino acid pattern shifts; no phosphoserineAmino acid profile
Calcium salt addedCalcium and ash up; phosphorus flatCalcium, phosphorus, ash, XRD
Maltodextrin or lactose dilutionProtein, peptide and calcium down togetherProtein, peptide, calcium, moisture

The first route matters most for a Kjeldahl specification. Melamine is about 67% nitrogen by mass, so a small addition lifts the protein figure without adding a peptide. Urea does the same on a smaller scale. Neither is visible in a protein result; both are visible in the amino acid profile and in a targeted screen.

How to write identity into the specification

  • “Casein phosphopeptides (milk); peptide ≥70.0% by HPLC with the integration range stated.”
  • “Protein ≥80.0% by Kjeldahl, factor 6.38, basis stated.”
  • “Calcium 2.0–4.0% by complexometric titration; phosphorus reported by ICP-OES.”
  • “Ash ≤10.0%; moisture ≤5.0%; particle size ≥95% through 80 mesh.”
  • “Allergen statement naming milk; lot number and site on the COA.”
  • “No added calcium salt; declare any carrier or mineral addition.”

Five questions for the supplier

  1. Which hydrolysis and membrane step made this lot, and what is the peptide distribution?
  2. What are the calcium and phosphorus figures, and what is the molar ratio?
  3. What is the protein factor and basis on the certificate?
  4. Can you supply the amino acid profile and a melamine screen on this lot?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single protein percentage does not. The product page carries the catalog specification; the COA page shows where each figure sits; the grades page covers the specification axes; the CPP versus casein page takes the parent-protein comparison further; the methods section describes the HPLC, titration and ICP methods; the quality page covers the retained sample.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation