02 Grade comparison

Casein phosphopeptide grades: peptide, calcium and physical form

Technical document 02 · Reviewed 2026-11-19 · Casein Phosphopeptides

On this page
  1. Why there is more than one grade
  2. The axes side by side
  3. Solubility, flow and colour
  4. The mass arithmetic
  5. What to write into the specification
  6. When a different ingredient is the better choice

Casein phosphopeptide (CPP) is sold as one catalog grade with a peptide minimum, a calcium range and a powder form, but several axes still move inside it: peptide content, calcium load, protein basis and particle form. The grade decision is about which axis the formula needs, because each one moves a different line: peptide content and calcium load change the ash and the mass per serving, while the physical form changes flow, dust and wetting. A higher peptide figure is not automatically the right purchase if the calcium contribution is the reason for the ingredient.

In one line

The CPP grade is set by the peptide content, the calcium load and the physical form; each axis moves a different line in the specification, not the name of the material.

Why there is more than one grade

CPP is a peptide fraction from casein, and the fraction is not a single molecule. The hydrolysis conditions set the peptide distribution; the membrane step decides how much of the smaller fraction is retained; the calcium addition, where it is used, sets the mineral load; the dryer and the mill set the physical form. Each of those is a specification decision, and a supplier can offer more than one combination.

The catalog grade fixes the middle of the road: protein ≥80%, peptide ≥70%, calcium 2.0–4.0%, ash ≤10.0%, 80 mesh. The axes below describe what moves when a formula needs something else.

The axes side by side

Axes inside the casein phosphopeptide specification
AxisCatalog positionWhat changes when it moves
Peptide content≥70.0% by HPLCA higher peptide figure is a separate specification; less non-peptide solid per gram
Calcium load2.0–4.0%The top of the range carries more calcium and more ash, and less peptide per gram
Protein basis≥80.0%, basis agreedDry basis versus as-is moves the figure by up to five points at the moisture ceiling
Physical form80 mesh powderGranulation changes flow, dust and wetting; the chemistry does not change
Colour windowOff-white to light tanA tighter window is a separate specification and can move the drying step
Mineral additionNot specifiedAn added calcium salt raises calcium and ash without raising phosphorus

The catalog grade is the 80 mesh powder; granulation is on request. The other columns are directions for a specification, not stock items, and each one has to be agreed in writing before the order.

Solubility, flow and colour

The powder dissolves in water to a clear to slightly turbid solution. Solubility is not unlimited: a concentrated stock may need warming or a longer dispersion time, and the calcium load can make the solution turbid as the concentration rises. Trial the concentration the formula will use rather than the one in a brochure.

Flow and dust change with the particle form. An 80 mesh powder flows well enough for a capsule filler but can dust in a stick-pack line; a granulated form reduces dust and wets more slowly. Neither is a defect, but the filling line notices the difference.

Colour is off-white to light tan. The window is wide because the raw milk and the drying step move it; a lot that is noticeably darker can point to a longer heat load or moisture pickup, while a lot inside the window is not an identity failure. Taste is a formula question: a peptide fraction is not tasteless, and the level that disappears in a capsule may be noticeable in a clear drink.

The mass arithmetic

The calcium figure is the first arithmetic. At 3.0% calcium, 1 g of powder carries about 30 mg calcium; at 2.0% it carries 20 mg, and at 4.0% it carries 40 mg. The same calcium target therefore needs half the powder at 4.0% as at 2.0%, which changes the capsule count or the stick weight before it changes anything else.

The calcium contribution is modest against the reference values. The EU nutrient reference value for calcium is 800 mg, so 30 mg is about 3.8% of it; the US Daily Value is 1,300 mg, so the same 30 mg is about 2.3%. A 500 mg capsule at 3.0% calcium carries about 15 mg calcium. A source-of-calcium claim under Regulation (EC) No 1924/2006 needs at least 15% of the EU reference value in the daily dose, which is 120 mg, and reaching that from CPP alone at 3.0% would take about 4 g of powder.

A 500 mg capsule at 80% protein carries about 0.4 g protein, so the ingredient is not a practical protein source at a capsule dose. If protein is the object, casein or collagen peptides are the ingredients to compare; CPP is bought for the peptide fraction and the mineral load.

What to write into the specification

  • “Casein phosphopeptides (milk), peptide content ≥70.0% by HPLC; state the integration range.”
  • “Protein ≥80.0% by Kjeldahl, factor 6.38, basis stated.”
  • “Calcium 2.0–4.0% by complexometric titration; report phosphorus by ICP-OES.”
  • “Ash ≤10.0%; moisture ≤5.0%; particle size ≥95% through 80 mesh.”
  • “Allergen statement naming milk; lot number and site on the COA.”
  • “Intended use and market confirmed before the order.”

A specification is only as good as the method beside each line. “Peptide 70%” without the HPLC method and the integration range is a number that two laboratories can read differently.

When a different ingredient is the better choice

If the formula needs protein, casein is the direct comparison: at ≥90% protein on a dry basis and ash ≤2.0%, it delivers more protein per gram with a neutral taste and a low mineral load. The micellar casein page sets out the form and its limits.

If the formula needs a hydrolysed protein for a clear beverage and the calcium is not wanted, collagen peptides deliver ≥90% protein with a defined molecular-weight distribution. The collagen peptide page covers the profile.

If the formula needs a calcium claim, a calcium salt delivers more calcium per gram than CPP at 2.0–4.0%. CPP is a peptide ingredient with a mineral load, not a calcium supplement. The reverse is also true: a protein powder does not carry the phosphopeptide fraction, and a formula built on that fraction should not be switched on a protein figure alone.

The catalog specification sits on the casein phosphopeptide product page; the certificate is read on the COA page; the comparison with the parent protein is on the CPP versus casein page; the HPLC and titration methods are in the methods section.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation