02.1 CPP vs casein

Casein phosphopeptides vs casein: the peptide fraction and the protein

Technical document 02.1 · Reviewed 2026-11-19 · Casein Phosphopeptides

On this page
  1. What hydrolysis does to casein
  2. The two ingredients side by side
  3. The protein figure measures different things
  4. Calcium and ash are part of the identity
  5. When each ingredient belongs in the formula
  6. The label and the allergen
  7. The purchase order decides it

Casein phosphopeptides (CPP) are made from casein, but they are not a stronger casein. Hydrolysis cuts the protein into smaller peptides and concentrates the phosphorylated fraction; the result has a peptide minimum, a calcium load and a solubility that the parent protein does not have. The two ingredients answer different formulation questions, and the protein figure is the worst single line for comparing them.

In one line

Casein phosphopeptides are a hydrolysed, phosphorylated fraction of casein, not a stronger casein: the peptide content, the calcium figure and the solubility are different measurements.

What hydrolysis does to casein

Casein is the main protein of milk, and in micellar casein it is sold as a dispersed protein with a protein minimum of 90% on a dry basis. CPP starts from casein and uses a food-grade protease to cut the chain; the phosphoserine clusters resist further breakdown, so the fraction that survives is enriched in phosphorylated peptides.

The membrane step then selects the peptide size, and the dryer turns the fraction into a powder. The parent protein is a large molecule; the CPP fraction is a mixture of much smaller peptides. That change in size is why the solubility, the taste and the calcium behaviour differ.

The two ingredients side by side

Casein phosphopeptides against micellar casein
PropertyCasein phosphopeptidesMicellar casein
Protein≥80.0% by Kjeldahl≥90.0% dry basis, N × 6.38
Peptide content≥70.0% by HPLCNot a specification line
Calcium2.0–4.0% (specified)Not on the specification; ash ≤2.0%
Ash≤10.0%≤2.0%
Moisture≤5.0%≤10.0%
SolubilitySoluble; clear to slightly turbidDispersible; swells, not a clear solution
Molecular sizePeptide fraction, much smaller than the parent proteinIntact micellar protein
Label nameCasein phosphopeptides (milk)Micellar casein (milk)

The table compares specifications, not rank. The casein column is the micellar grade on this site; caseinate is a different casein ingredient with its own ash and sodium or calcium load.

The protein figure measures different things

A 90% protein figure for casein and an 80% figure for CPP are not points on the same scale. The casein figure is protein on a dry basis with N × 6.38; the CPP figure is a minimum with the basis to be agreed, and the peptide line sits underneath it. The CPP peptides are part of the protein figure, so the two lines overlap rather than add.

If the purchase is for protein, casein delivers more protein per gram and carries a low ash. If the purchase is for the phosphopeptide fraction, the protein figure says little: a casein powder can meet 80% protein and contain little of the peptide fraction the CPP specification measures, and a CPP that meets 80% protein can still miss the 70% peptide line.

Read the peptide line with its method. The HPLC distribution and the integration range decide what the figure means; a peptide number without them is not comparable across suppliers.

Calcium and ash are part of the identity

Micellar casein carries colloidal calcium phosphate, but the casein specification does not state a calcium figure; it controls the mineral load through ash ≤2.0%. CPP states calcium at 2.0–4.0% and allows ash up to 10.0%, so the mineral load is a specification line rather than a background.

That is why the CPP calcium figure has to be read with phosphorus. Bound calcium travels with the phosphopeptide; an added calcium salt raises calcium and ash without raising phosphorus. A CPP buyer who needs the peptide fraction should ask for the pair, not the calcium alone.

The calcium load also changes the mass. At 3.0% calcium, 1 g of CPP carries about 30 mg calcium, while casein at its ash ceiling carries a smaller and unspecified amount. A formula built on CPP for its calcium is a different formula from one built on casein for its protein.

When each ingredient belongs in the formula

Choose casein when the object is protein: a powder, bar or drink that needs a high protein figure per gram, a neutral taste and a low mineral load. It disperses and thickens, which suits a bar or a shake, and it carries the milk allergen without the peptide specification.

Choose CPP when the object is the phosphorylated peptide fraction and its calcium load: a capsule, a tablet or a powder where the peptide and the mineral are the reason for the ingredient. The solubility suits a drink, but the calcium equilibrium and the taste have to be trialled in the matrix.

Do not substitute one for the other on a protein figure. A casein lot that meets 90% protein is not a CPP, and a CPP lot that meets 80% protein is not a protein source in the sense that a protein powder is.

The label and the allergen

Both ingredients are milk-derived, so both carry the milk allergen declaration. The names are not interchangeable: “micellar casein” describes a milk protein, while “casein phosphopeptides” describes a peptide fraction, and a label that uses one name for the other is inaccurate even when both come from milk.

The regulatory route is also different. Casein has a long history of food use; a CPP is a processed fraction, and whether it is inside a novel-food framework, a GRAS basis or another route is a destination question for the buyer’s regulatory team. The parent ingredient’s history does not automatically cover the hydrolysate.

Check the claim arithmetic before the label is set. A CPP at 2.0–4.0% calcium delivers 10–20 mg calcium in a 500 mg capsule, a small fraction of the EU reference value of 800 mg. The claim belongs to the finished product, not to the ingredient name.

The purchase order decides it

Write the ingredient, the source and the specification. For casein: micellar casein, protein ≥90.0% dry basis with N × 6.38, ash ≤2.0%, moisture ≤10.0%. For CPP: casein phosphopeptides (milk), peptide ≥70.0% by HPLC, protein ≥80.0% with the factor and basis, calcium 2.0–4.0%, ash ≤10.0%.

Then write the use level as powder mass and show the protein and calcium it delivers. A purchase order that names only “casein” or only “CPP” has not specified either ingredient, and a switch between them is a new specification, a new label and a new allergen review.

The catalog specification for CPP sits on the casein phosphopeptide product page, with the grade axes on the CPP grades page. The parent protein is specified on the micellar casein page, with the form comparison on its grade page. For a hydrolysed protein with a different amino acid profile, see collagen peptides; the HPLC and titration methods are in the methods section, and the release file is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation