01 COA & batch testing

What the COA for bitter melon peptides actually contains

Technical document 01 · Reviewed 2026-11-19 · Bitter Melon Peptides

On this page
  1. The certificate as a test report
  2. Protein, peptide and the basis behind both
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

The certificate for a bitter melon peptide lot reports appearance, identification of the protein and peptide profile, protein by Kjeldahl, peptide content by HPLC, ash, moisture, heavy metals, microbiology and particle size. Each line needs its method and release limit, with the measured result in its own column. The limits below are the catalog specification; the batch COA confirms a particular lot.

In one line

A bitter melon peptide certificate is complete only when the protein figure, the peptide figure and the ash and moisture beside them carry their methods and their basis.

The certificate as a test report

A certificate is useful when it can be audited line by line: what was measured, which method produced the number, and which limit the lot was released against. A row that says only “conforms” asks the reader to accept a conclusion without the evidence. The identity line decides whether the powder is a bitter melon peptide rather than another plant hydrolysate.

Identity, protein, peptide and contaminants · bitter melon peptides
ParameterMethodRelease limit
AppearanceVisualOff-white to light yellow powder
IdentificationProtein and peptide profile against referenceConforms
ProteinKjeldahl; factor and basis stated≥80.0%
Peptide contentHPLC; method and cut-off stated≥70.0%
AshGravimetric, furnace≤8.0%
MoistureLoss on drying≤7.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

The source is a parameter too. The certificate should name the species, Momordica charantia, and the plant part, because fruit-derived and seed-derived powders are different raw materials. The catalog fixes the species, not the plant part.

Protein, peptide and the basis behind both

Kjeldahl measures nitrogen; the protein figure is nitrogen multiplied by a conversion factor. For a plant peptide the common convention is N × 6.25, which assumes nitrogen is about 16% of the protein; at that factor an 80.0% result corresponds to 12.8% nitrogen. A certificate that prints 80.0% without the factor has not shown how the number was reached.

The catalog gives protein as ≥80.0% and peptide as ≥70.0% by HPLC, but it does not print a moisture basis for the protein. The basis changes the number: 80.0% on a dry basis is about 74.4% as-is at the 7.0% moisture limit, while 80.0% as-is is about 86.0% on a dry basis.

Peptide content is a separate measurement. HPLC separates the peptide fraction from free amino acids and other small nitrogenous compounds and reports it against the sample or the protein. The catalog names HPLC but not the column, mobile phase or cut-off, so those belong in the agreed method.

The gap is informative. At 80.0% protein and 70.0% peptide, ten points of the protein figure are outside the peptide fraction: free amino acids, small peptides below the cut-off, or non-protein nitrogen. A wider gap is a reason to ask what the method measured, not to reject the lot.

Release limit versus batch result

The release limit is the acceptance boundary; the batch result is what the laboratory measured. Both belong on the page, in separate columns, with the method beside them. A result column filled with the specification range is a copy of the gate, not a result.

What the result column should contain
ParameterRelease limitResult column
Protein≥80.0%A measured percentage with the factor and the basis
Peptide content≥70.0% by HPLCA measured percentage with the method and cut-off
Ash≤8.0%A measured percentage
Moisture≤7.0%A measured percentage
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot

For protein and peptide the result needs its basis and method, not only a percentage. For microbiology the evidence is a count plus an absence statement; a single “pass” hides which organism was tested. The lot code on the certificate should match the pouch, the drum and the retained sample.

What moves between batches

The raw material moves first. Cultivar, maturity at harvest, growing season and the plant part all change the protein load and the non-protein fraction. A late-season lot is not the same raw material as an early pick, even when the species is unchanged.

The hydrolysis step moves the peptide figure. Enzyme, dose, time, temperature and pH decide how far the protein is cut, and a longer hydrolysis raises the peptide content while it can also raise the bitterness. Decolourisation changes colour, filtration changes ash and the fine fraction, and spray drying fixes moisture and particle size.

Colour and taste are the least quantitative lines and often the most revealing. A green tint points to a less completely decolourised lot; a darker tan to a hotter drying step or a longer hold. Bitterness can move outside what a flavoured stick pack will mask while the protein figure still passes. Ask for the retained sample and the storage record rather than rejecting on colour alone.

When to order an outside test

Order an independent test for a new source, a first shipment into a regulated market, a claim the certificate does not prove, or a disputed result. The panel answers the open question: protein by Kjeldahl with the factor, peptide by HPLC with the method and cut-off, the amino acid profile, ash and moisture, ICP-MS for heavy metals, and microbiology.

Add a source-specific test when the botanical identity is in doubt. A PCR method for Momordica charantia can show that the declared species is present; a PCR screen for soy, pea and wheat can show that another plant source is present. For non-protein nitrogen, the amino acid sum against Kjeldahl is the first screen, and melamine by LC-MS/MS is the specific check. Ask for the detection limit of each screen.

Chain of custody matters. The sample tested should be the sample retained, and the report should identify the lot. When a result is contested, give the referee the retained sample, the certificate and the specification, and ask for the tests that separate the possible explanations.

What to compare between suppliers

Put six lines side by side: species and plant part; protein result with factor and basis; peptide result with method and cut-off; ash and moisture; heavy metals and microbiology; and the allergen and cross-contact statement. Two quotations that agree on protein but differ on method or plant part are not describing the same powder.

The second layer is traceability: who made the lot, which raw material and hydrolysis conditions were used, and which drying and milling steps were applied. The catalog specification sits on the bitter melon peptides product page. The source tests are on the identity page; the grade choices on the grades page; the method vocabulary in the methods section; the release workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation