How to prove a lot is bitter melon peptides
A bitter melon peptide lot is identified by four agreeing measurements: protein by Kjeldahl, peptide content by HPLC, a source-specific test or marker profile, and an ash-and-moisture mass balance. The document names the species and plant part; the measurements test the claim. The protein figure alone can be met by another plant protein or by non-protein nitrogen; the peptide figure and the source test are what close the gap.
Identity is a set of agreeing measurements: the species and plant part, the protein and peptide figures, and a source-specific test, not one assay.
The four identity layers
The document names the species and plant part, but a name on a certificate is not evidence. The four measurements below are separate questions, and each needs its own result. A supplier who answers only the protein figure has described the paperwork, not the powder.
| Layer | Question | Test | What it proves |
|---|---|---|---|
| Protein | How much nitrogenous material is present? | Kjeldahl with the factor stated | Protein, not the source |
| Peptide | How much of it is peptide? | HPLC with the method and cut-off | The peptide fraction |
| Source | Is it Momordica charantia? | PCR or a marker profile | The botanical source |
| Mass balance | Is it diluted? | Ash, moisture, amino acid profile | Consistency of the numbers |
The four are independent. A lot can be genuine bitter melon and still be diluted; it can pass protein and peptide and still contain soy; it can be the right species and the wrong plant part. Each needs its own evidence, and the evidence belongs in the batch file rather than in a marketing sentence.
The protein-to-peptide gap and the ash ratio
The simplest screen is the gap between protein and peptide. At the catalog figures, 80.0% protein and 70.0% peptide leave ten points outside the peptide fraction. Free amino acids, small peptides below the cut-off and non-protein nitrogen sit in that gap. A gap of ten points is expected; a gap of twenty is a question.
The ash figure is a second ratio. At ≤8.0% ash and ≥80.0% protein, the ash-to-protein ratio is at most 0.10. A lot with 80% protein and 12% ash carries either a mineral load or a neutralisation salt that the specification did not intend. Ash is not a peptide measurement, but it is simple to check and hard to hide.
Non-protein nitrogen is the case that most needs the amino acid profile. Kjeldahl counts nitrogen from protein, free amino acids, urea, melamine and ammonium salts alike. The amino acid sum, expressed as protein, should sit close to the Kjeldahl figure. A shortfall of five or more points suggests nitrogen that is not protein.
Where XRD and FTIR stop
Spray-dried peptide powder is amorphous, so an X-ray diffraction scan shows a broad halo rather than sharp peaks. That halo is consistent with a spray-dried hydrolysate but does not identify the species. Sharp reflections point to a crystalline addition: an amino acid used to lift the nitrogen figure, an inorganic salt, a sugar that crystallised in storage, or a mineral carrier.
FTIR gives a functional-group fingerprint. Absorbance near 1650 cm⁻¹ (amide I) and 1545 cm⁻¹ (amide II) comes from the peptide backbone; the carbohydrate region carries residual sugar and any carrier. FTIR confirms the material class quickly, but it cannot tell bitter melon from soy or pea. Use it as a screen, not as identity. The methods section sets out what each technique proves and what it leaves open.
What adulteration looks like
| Route | What it changes | Signal | Test |
|---|---|---|---|
| Another plant protein | Raises protein with a different source | Soy, pea or wheat marker; amino acid shift | PCR; amino acid profile |
| Non-protein nitrogen | Raises Kjeldahl without adding protein | Protein up, amino acid sum flat | Amino acid profile; melamine by LC-MS/MS |
| Free amino acids | Raises protein; peptide fraction unchanged | Peptide low against protein | Peptide HPLC; amino acid profile |
| Maltodextrin or sugar | Lowers protein; raises carbohydrate | Protein down, carbohydrate up | Mass balance; sugar HPLC |
| Juice powder, not hydrolysed | Peptide low; larger molecules | Peptide below 70%; broad size curve | Peptide HPLC; molecular-weight distribution |
| Plant-part substitution | Protein and ash shift; source record differs | Material from a different plant part than declared | Source record; marker profile; PCR |
The first two routes matter most for a plant peptide at 80% protein. Another protein is easy to add and shows in the amino acid profile; non-protein nitrogen is harder to see and needs the amino acid sum plus a specific method. Colour is the weakest signal: off-white to light yellow is a wide window and does not prove anything.
How to write identity into the specification
- “Bitter melon peptides, Momordica charantia; plant part stated.”
- “Protein ≥80.0% by Kjeldahl; factor and moisture basis stated on the COA.”
- “Peptide content ≥70.0% by HPLC; column, mobile phase and cut-off stated.”
- “Ash ≤8.0%; moisture ≤7.0%; ≥95% through 80 mesh.”
- “No added plant protein, free amino acids or non-protein nitrogen.”
- “Amino acid profile reported; source PCR or marker profile on request.”
- “Allergen and cross-contact statement names the source and the shared lines.”
Five questions for the supplier
- Which species and plant part were used for this lot?
- What conversion factor and moisture basis produced the protein figure?
- Which HPLC method and cut-off produced the peptide figure?
- What is the amino acid profile, and how does it compare with the Kjeldahl result?
- Will you support a source-specific PCR or marker test, and a joint re-test on the retained sample?
Five direct answers amount to an identity file. A single protein percentage does not. The product page carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page covers the peptide and form choices; the quality page describes the retained sample and release file.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation