Bitter melon peptide grades: protein, peptide and form
Bitter melon peptides are specified on two figures and a physical form: protein at ≥80.0% by Kjeldahl and peptide content at ≥70.0% by HPLC, as an 80 mesh powder or a granulated powder. The grade decision is what changes when the peptide content, the plant part, the colour or the particle size is adjusted for a dosage form. The certificate follows the grade; it does not define it.
The grade is the peptide content and the physical form, not the protein percentage alone; granulation changes the line, and a dilution changes the label.
Why one name covers several powders
Bitter melon peptides are described by a process, not by a single molecule. The species is fixed, but the plant part, the degree of hydrolysis, the decolourisation and the drying step are process choices, and each one changes the powder that arrives. Two lots can both pass ≥80.0% protein and ≥70.0% peptide and still differ in bitterness, colour and flow.
The catalog names a standard 80 mesh powder. The first grade question is therefore whether that standard powder fits the line, not whether a higher number exists. A capsule line, a stick pack and a tablet press want different flow, density and taste; the peptide chemistry can be identical while the handling is not.
The grade choices side by side
| Grade | Protein / peptide | Form | Fits | Watch |
|---|---|---|---|---|
| Catalog powder | ≥80.0% / ≥70.0% | 80 mesh powder | Capsules, tablets, blends | The baseline for every comparison |
| Higher-peptide cut | ≥80.0% / above 70.0%, agreed | Powder | Lower powder weight per serving | More bitter; lower yield |
| Granulated | Same as the base lot | Granules on request | Sachets, tablets, filling lines | Slower wetting; density shift |
| Lower-protein dilution | Below 80.0%, with a carrier | Powder | A lower dose per gram | Carrier on the label; not the catalog grade |
The first three rows are variations of the same material. The fourth is a different specification. A dilution can look like a grade on a quotation because the protein percentage is the only line that moved, but the label now carries a carrier and the peptide content per gram is lower. If the dosage form needs a lower protein load, a dilution is legitimate; it should be ordered as one, with the carrier named.
What changes in the drum
Solubility is good: the powder dissolves in water to a clear to slightly turbid solution. That is why a stick pack or a drink mix is a natural fit, and why haze at high concentration is a formulation question rather than a grade failure. In a pale or clear drink the powder's colour and any turbidity are visible, so the appearance belongs in the bench trial.
The powder is hygroscopic. A finer powder picks up moisture faster and can cake; a granulated powder has less surface and flows better, but it wets more slowly. Bitterness is intrinsic to the material. A finer powder disperses faster and can make the bitterness more immediate, while granulation delays it slightly. Neither change removes the taste.
Colour runs from off-white to light yellow. A green tint points to a decolourisation issue, not to a peptide grade; it can sit inside the appearance window and still be visible in a pale drink. The grade specification should say whether the colour is measured visually or against a standard.
What the dosage form needs
Capsules and tablets take the standard 80 mesh powder. For capsules the constraint is bulk density and fill weight; for tablets it is flow and compressibility, and a granulated grade is often the practical choice. Bitterness is less exposed in a swallowed capsule, but the fill still tastes bitter if the capsule is opened or chewed.
Stick packs and drink mixes are the harder case. The dose has to dissolve, the bitterness has to be carried by the flavour system, and the powder has to flow on the filling line. A flavour system and a sweetener can mask part of the bitterness, but the bench trial has to run at the label dose. A granulated grade helps flow; it does not remove the taste.
Gummies and chews add water and heat. The powder is hygroscopic, and the matrix water can make the mix sticky before the chew sets. The grade choice is secondary to the process here: a granulated powder may flow better, but the water activity and the flavour system decide whether the bitterness is acceptable.
What to write into the specification
- “Bitter melon peptides, Momordica charantia; plant part stated.”
- “Protein ≥80.0% by Kjeldahl; factor and moisture basis stated on the COA.”
- “Peptide content ≥70.0% by HPLC; column, mobile phase and cut-off stated.”
- “Ash ≤8.0%; moisture ≤7.0%; ≥95% through 80 mesh.”
- “Appearance off-white to light yellow; bitterness and colour standard agreed on the retained sample.”
- “Granulation or carrier, if any, named on the specification and the label.”
When another material is the better fit
If the brief is a neutral-tasting protein at a high dose, a bitter melon peptide is the wrong starting point. Soy protein isolate or pea protein isolate will carry the protein with a different taste and a different label. If the label needs ≥90% protein, an 80% peptide is not a direct swap: the powder weight per serving changes.
If the formula is a clear beverage at high concentration, test the haze before the grade is fixed. A powder that dissolves cleanly at 1% can turn a 3% drink turbid, and the grade that solves the flow problem may not solve the appearance. The bitter melon versus soy comparison sets out the source, taste and label differences; the COA page shows how the figures are reported; the product page carries the catalog specification.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation