06 Identity & adulteration

How to prove a zinc sulfate lot is the monohydrate

Technical document 06 · Reviewed 2026-11-20 · Zinc Sulfate Monohydrate

On this page
  1. Identity evidence, layer by layer
  2. What the zinc, sulfate and water figures should show
  3. IR and diffraction: checking the solid
  4. What substitution looks like
  5. Identity lines for the specification
  6. Five questions to settle before approval

A monohydrate lot is identified by agreement, not by one number: the document names CAS 7446-19-7, complexometric titration returns 35.0–38.0% zinc, a sulfate determination confirms the anion, a water determination fits the monohydrate rather than the heptahydrate, and IR or X-ray diffraction matches the monohydrate reference. Zinc alone cannot separate the hydrates, because the heptahydrate returns 22.7% and the anhydrous salt 40.5%.

In one line

A monohydrate lot is proved when the zinc, sulfate and water results agree and the solid-state pattern matches, not by a single zinc percentage.

Identity evidence, layer by layer

A name on a certificate is a claim; the tests are the evidence. The table separates the questions. A supplier who answers only the first question has described the label, not the drum.

What each identity test establishes
EvidenceQuestion it answersMethodWhat it establishes
PaperworkDoes the document name the hydrate?Name, CAS, formulaOnly the label
ZincIs the zinc figure right?Complexometric titrationZinc content, not hydration
SulfateIs the anion sulfate?Titration or gravimetric sulfateConfirms the salt and balances the mass
WaterIs it the monohydrate?Total water, plus LOD for free moistureHydration state
CrystalIs the solid the monohydrate?IR; XRD for a disputeThe hydrate in the drum

The catalog identity is a conformity statement: zinc and sulfate conform. It is a workable release gate, but it does not put a number on the sulfate or the water. If the hydrate is challenged, ask for those numbers and for the diffraction pattern.

What the zinc, sulfate and water figures should show

The formula sets the expected figures. Pure ZnSO4·H2O contains 36.43% zinc, 53.53% sulfate and 10.04% water. Zinc and sulfate are present in a 1:1 molar ratio, which is a mass ratio of 36.43 ÷ 53.53 = 0.681. One gram of zinc corresponds to 179.45 ÷ 65.38 = 2.745 g of salt.

The catalog window of 35.0–38.0% zinc maps to 96.1–104.3% of the monohydrate formula. A result at the top means less water than the formula; a result at the bottom means more water or a diluent. That is why the zinc line is read with the sulfate and the water, not alone: high zinc with low water suggests an anhydrous fraction, low zinc with normal sulfate suggests a diluent, and high water with low zinc suggests surface moisture.

The water line needs a note. The catalog's LOD is a free-moisture test; the monohydrate keeps its crystal water until above 238 °C, so the 10.0% does not show up there. To prove the hydrate by mass balance, order total water as a separate determination.

A hydrate blend shows the same way. Monohydrate plus anhydrous salt can sit inside the zinc window while its total water falls with the anhydrous share; adding sodium sulfate lowers zinc and introduces sodium. Zinc reports the element, sulfate reports the anion, water reports the hydrate.

IR and diffraction: checking the solid

IR is the usual release check: it is quick, and it sees the sulfate and water bands together. With a reference it can distinguish the monohydrate from the heptahydrate, though the spectra are close and a library hit is only as reliable as the library. Name the reference and the band region.

X-ray diffraction is more direct: does the solid give the monohydrate pattern? Each solid has its own unit cell, so the peaks sit in different places and a mixture shows both sets. XRD does not measure purity or water, but it is direct evidence that the crystal is the hydrate named on the sheet.

A match needs the reference pattern and a detection limit. A report that says only “XRD conforms”, with no pattern and no reference, adds little. Order it when a hydrate claim is challenged, or when two sources are being weighed for a specification change.

What substitution looks like

Hydrate and grade substitutions, and how they show
What goes wrongHow the figures moveSignalTest
Heptahydrate supplied as monohydrateZinc falls; total water risesZinc near 22.7%; water highTitration, total water, XRD
Anhydrous salt blended inZinc rises; total water fallsZinc above 38.0%; water lowTitration, total water, XRD
Sodium sulfate addedZinc falls; sodium risesSodium present; sulfate near normalICP-OES, mass balance
Magnesium sulfate substitutedZinc falls; magnesium risesMagnesium present; different patternICP-OES, XRD
Zinc oxide blended inInsoluble zinc; sulfate fallsHazy solution; sulfate below 53.5%Solubility, sulfate, XRD
Technical gradeHeavy metals risePb, Cd or As over the limitICP-MS on the lot
Free waterLOD climbs; cakingLOD over 1.0%; sieve blockedLOD, sieve, flow

Zinc sulfate is a commodity, so the usual problems are grade and hydrate rather than a clever fake. A technical grade can pass zinc and fail the metals; a heptahydrate can pass a wide zinc window and fail the water. Colour is the weakest clue: white to off-white covers every hydrate, and a yellow tint points to iron.

Identity lines for the specification

  • “Zinc sulfate monohydrate, CAS 7446-19-7, ZnSO4·H2O.”
  • “Zinc 35.0–38.0% by complexometric titration; name the basis.”
  • “Zinc and sulfate conform; report the sulfate result.”
  • “Loss on drying ≤1.0%; total water by Karl Fischer on request.”
  • “IR versus a named reference; XRD if a dispute arises.”
  • “Heavy metals by ICP-MS, element by element; microbiology as listed.”
  • “No hydrate or grade change without written change control.”

Five questions to settle before approval

  1. What hydrate is this, and which CAS number is printed on the certificate?
  2. What zinc and sulfate results were obtained, and by which methods?
  3. What is the total water, and does the mass balance close?
  4. May we see the IR spectrum and, if needed, an XRD pattern with its reference?
  5. If the lot is challenged, will you join a retest of the retention sample?

An identity file is these answers together. One zinc percentage is not the file. The product page has the catalog data; the heptahydrate page has the other hydrate's figures; the COA page shows where each result sits; the grades page compares the two; the methods library covers titration, water and diffraction; the quality page covers release and retest.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation