01 COA & batch testing

What the COA for zinc sulfate monohydrate reports

Technical document 01 · Reviewed 2026-11-20 · Zinc Sulfate Monohydrate

On this page
  1. The certificate as a test report
  2. The basis: zinc, sulfate and the monohydrate scale
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

A zinc sulfate monohydrate certificate lists appearance, zinc and sulfate identification, zinc by complexometric titration at 35.0–38.0%, loss on drying at ≤1.0%, the metals panel, microbiology and mesh. Zinc is the assay on this product; the catalog has no separate purity line written as monohydrate. The LOD line is a surface-moisture gate at the usual drying condition, not the 10.0% water in the formula.

In one line

The zinc figure is the assay on a zinc sulfate monohydrate certificate, and the loss-on-drying line measures free moisture at the usual drying condition, not the 10.0% crystal water the formula carries.

The certificate as a test report

An auditable certificate gives three things per line: what was measured, the method behind the number, and the limit the lot had to meet. A line that says only “conforms” gives a conclusion without the measurement. For a hydrate, the decisive lines are zinc, sulfate and water, because together they name the solid.

Release tests for zinc sulfate monohydrate
TestMethodLimit
AppearanceVisualWhite to off-white powder
IdentificationComplexometric titration (zinc and sulfate)Zinc and sulfate conform
ZincComplexometric titration35.0–38.0%
Loss on dryingGravimetric, specified drying condition≤1.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Appearance is the least specific line. White to off-white covers the monohydrate, a partly anhydrous lot and a diluted blend. A yellow cast can indicate iron; the metal panel is the quantitative check.

The basis: zinc, sulfate and the monohydrate scale

The formula supplies the arithmetic. ZnSO4·H2O is 179.45 g/mol: 65.38 zinc, 96.06 sulfate, 18.02 water. The percentages are 36.43% zinc, 53.53% sulfate and 10.04% water, and 179.45 ÷ 65.38 = 2.745 g of salt per gram of zinc.

Against that, the catalog window of 35.0–38.0% zinc is 96.1–104.3% of the formula. The top of the window means some water has gone; the bottom means extra water or a diluent. The zinc line cannot choose between those, so the sulfate and water results are needed.

The LOD test runs at the usual 105 °C. At that temperature the monohydrate keeps its crystal water, which is not released until above 238 °C, so the result is surface moisture. The ≤1.0% limit belongs to that measurement. A total-water figure is a different test and should be ordered separately.

A supplier's “purity” figure is ambiguous on this product because there is no assay as monohydrate. Ask whether the number is zinc as-is, zinc on the dried basis, or ZnSO4 content; without the basis it cannot be compared with the catalog.

Release limit versus batch result

A limit is a gate; a result is a measurement. The certificate should show both, in separate columns, with the method named. If the result column simply repeats the range, no measurement has been reported.

What the result column should show
ParameterLimitResult column
Zinc35.0–38.0%A measured percentage by complexometric titration
IdentificationZinc and sulfate conformThe zinc and sulfate results, not only the word “conforms”
Loss on drying≤1.0%A measured percentage at the stated drying condition
Heavy metalsPer elementA number in mg/kg for every element
MicrobiologyCounts and absenceThe colony count and the absence result
Particle size≥95% through 80 meshThe percentage that passed the sieve

Two quick checks. First, convert the zinc result to the formula scale: 35.0% is 96.1% and 38.0% is 104.3%, so a figure outside the window means another hydrate or another salt. Second, add zinc and sulfate: a pure monohydrate gives 89.96%, and the rest is water, which the LOD line does not measure. A gap that total water does not explain points to a diluent.

What moves between batches

Surface moisture moves first. An open pouch or a humid store raises the LOD, cakes the powder and can fail the sieve while the zinc stays in range. A change of mill or of the 80 mesh screen moves the particle-size result without any chemical change.

Iron shows on appearance before it shows on the zinc line. A different zinc feed or purification step can leave a yellow cast, and the metal panel is where it is measured. A zinc result near an edge should also be read against the sulfate: the window is wide enough to hide a dilution at the bottom and an anhydrous fraction at the top.

Look at the direction of travel across lots, not one result near an edge: zinc moving up, LOD rising, or a new colour. Keep the code on the certificate tied to the pack and to the retention sample.

When to order an outside test

An outside test makes sense when the source is new, when a lot is the first into a regulated market, when the hydrate is disputed, or when technical grade is suspected. The panel should differ from the certificate: complexometric zinc, a sulfate determination, total water by Karl Fischer or thermogravimetry, ICP-MS, microbiology, and IR or XRD if the hydrate is in question.

Every screen should carry a detection limit. “Not detected” without a limit describes the method, not the sample. Keep the tested sample as the retention sample and identify the lot on the report. If a result is challenged, hand the referee the retention sample, the certificate and the specification, and ask for tests that separate the hydrates.

What to compare between suppliers

Six lines make a comparison: hydrate and CAS; zinc and sulfate results; LOD and total water; metals and microbiology; particle size; pack and lot code. Offers that agree on zinc can still describe different solids if the hydrate or the water differs.

Traceability is the second layer: who made the lot, where the zinc came from, how it was purified, and the drying and milling history. The catalog data is on the product page; the heptahydrate's figures are on the heptahydrate page; the hydrate tests are on the identity page; the methods are in the methods library; the release steps are described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation