Zinc sulfate monohydrate or heptahydrate: the grade decision
Zinc sulfate monohydrate (ZnSO4·H2O, CAS 7446-19-7) carries 36.4% zinc; the heptahydrate (ZnSO4·7H2O, CAS 7446-20-0) carries 22.7%. They are the same salt at two hydration states, so choosing between them moves the fill weight, the water load and the label calculation, not the purity. The catalog monohydrate is an 80 mesh powder at 35.0–38.0% zinc with LOD at ≤1.0%.
The monohydrate and the heptahydrate are the same salt at different water content, 36.4% zinc against 22.7%, so the grade decision is a fill-weight and water-load decision, not a purity decision.
One salt, two hydrates
Zinc sulfate takes seven waters when it crystallises. Drying removes six and leaves the monohydrate; more heat removes the seventh and gives the anhydrous salt. The monohydrate is the middle hydrate, and the trade calls it “dried” even though the name describes a process, not a formula.
The process name causes trouble. A partly anhydrous lot can be sold as monohydrate and can sit at the top of a wide zinc range, so the certificate's zinc and water results identify the solid better than the drum label.
Nor is the choice a purity choice. Both are zinc sulfate; the heptahydrate simply carries more water per gram. The formulator weighs salt, the label declares zinc, so the hydrate belongs in the specification and the zinc figure belongs in the dose.
The two hydrates side by side
| Property | Monohydrate | Heptahydrate |
|---|---|---|
| Formula | ZnSO4·H2O | ZnSO4·7H2O |
| CAS number | 7446-19-7 | 7446-20-0 |
| Molar mass | 179.45 | 287.55 |
| Zinc, calculated | 36.4% | 22.7% |
| Water, calculated | 10.0% | 43.9% |
| Salt per gram of zinc | 2.75 g | 4.40 g |
| Form | White to off-white powder | Colourless crystals or white powder |
| Mesh | ≥95% through 80 mesh | ≥95% through 40 mesh |
The factor is 36.4 ÷ 22.7 = 1.60. A 25 kg drum of monohydrate holds about 9.1 kg of zinc; the heptahydrate holds about 5.7 kg. The monohydrate is the more concentrated grade, and the fill weight follows that concentration.
Powder, water and flow
The catalog powder is white to off-white at 80 mesh; the heptahydrate comes as colourless crystals or a white powder at 40 mesh. The finer monohydrate dissolves and disperses quickly but dusts and compacts more easily. Granulated material is available on request when flow matters.
Both are hygroscopic and both solutions are acidic. The monohydrate adds about 10 g of water per 100 g to a blend; the heptahydrate adds about 44 g. That difference matters with a moisture-sensitive active or a carbonate, and the acidity matters for taste, carbonate reactions and mild-steel contact.
The monohydrate is not the anhydrous salt. Its water is held until above 238 °C, so a 105 °C LOD reads surface moisture rather than the 10.0% in the formula. That is how a one-tenth-water material can carry a ≤1.0% LOD limit.
Zinc arithmetic and the label
The label declares zinc, so the weigh-up starts from zinc. At the calculated figures, 10 mg of zinc is 27.5 mg of monohydrate or 44.0 mg of heptahydrate; 15 mg is 41.2 mg or 66.0 mg. These are examples of the arithmetic, not an intake recommendation.
The EU reference intake is 10 mg zinc per day, so 10 mg is 100% of the nutrient reference value; the US daily value is 11 mg. The finished dose is checked against the destination's upper level, and that check uses elemental zinc.
The salt weight changes the dosage form. The monohydrate needs about 62% of the heptahydrate weight for the same zinc, which can free space for another ingredient or shrink the capsule. A straight swap is the error: 44.0 mg of monohydrate gives 16.0 mg of zinc against a 10 mg label, and 27.5 mg of heptahydrate gives 6.3 mg of zinc.
Specification lines for the monohydrate
- “Zinc sulfate monohydrate, CAS 7446-19-7, ZnSO4·H2O.”
- “Zinc 35.0–38.0%, complexometric; state the basis.”
- “Zinc and sulfate conform on identification.”
- “LOD ≤1.0% at the named condition; total water on request.”
- “80 mesh powder, ≥95% through; granulated on request.”
- “Metals and microbiology per the catalog; report each element.”
- “Hydrate fixed on the order; no substitution without change control.”
This page covers the monohydrate. The heptahydrate has a different zinc range, water range and mesh, and it cannot replace the monohydrate at the same weight. A change of hydrate goes through change control with a new fill weight and label check.
When the other grade is the wrong choice
Do not keep a heptahydrate fill and switch to the monohydrate: the capsule would carry about 60% more zinc than declared. The reverse is also a label failure: a monohydrate fill used as heptahydrate gives about 37% less zinc, and every release test on the salt can still pass.
The heptahydrate is the right choice when the formula and fill already assume 22.7% zinc and a change would reopen the label. The monohydrate is the right choice when fill space or water load is the constraint. Neither is a purity upgrade.
The monohydrate product page carries the catalog data. The heptahydrate page carries its own figures; the level-four comparison takes the water and label arithmetic further; the COA page shows how the zinc result is reported; the methods library covers titration and water; the quality page covers release.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation