Zinc sulfate monohydrate vs heptahydrate: water, zinc and the label
A gram of zinc sulfate monohydrate contains 0.364 g of zinc; a gram of the heptahydrate contains 0.227 g. The monohydrate is the more concentrated form by a factor of 1.6 because it holds one water molecule instead of seven. The label still declares elemental zinc, so a switch has to be worked through the fill weight, not by leaving the label figure alone.
A gram of the monohydrate delivers 0.364 g of zinc against 0.227 g from the heptahydrate, so a straight weight-for-weight switch raises the zinc in the capsule by about 60%.
Two hydrates, one salt
Both grades are zinc sulfate; the difference is hydration. The monohydrate is ZnSO4·H2O (CAS 7446-19-7, 179.45 g/mol); the heptahydrate is ZnSO4·7H2O (CAS 7446-20-0, 287.55 g/mol). The six extra waters account for the mass difference and for the fact that the two cannot be exchanged gram for gram.
“Dried zinc sulfate” is a trade name, not a formula. It normally means the monohydrate, but a partly anhydrous lot can still be sold under the name and can sit inside a broad zinc range. The certificate's zinc and water results describe the solid better than the drum label does.
The solids also age differently. The heptahydrate effloresces in dry air at room temperature, shedding surface water; the monohydrate keeps its single water until above 238 °C. That is the reason a monohydrate sheet can show LOD at ≤1.0% while the formula holds 10.0% water.
The zinc figure per gram
| Measure | Monohydrate | Heptahydrate |
|---|---|---|
| Zinc per gram of salt | 0.364 g | 0.227 g |
| Salt needed for 10 mg zinc | 27.5 mg | 44.0 mg |
| Salt needed for 15 mg zinc | 41.2 mg | 66.0 mg |
| Water per 100 g of salt | 10.0 g | 43.9 g |
| Zinc in a 25 kg drum | 9.1 kg | 5.7 kg |
The ratio 0.364 ÷ 0.227 = 1.60 is the conversion. The monohydrate is not a purer grade; it is a drier one, and the zinc per gram is higher for that reason. Because the catalog range is 35.0–38.0%, a label calculation should use the batch result, not the 36.4% theoretical figure.
The same arithmetic works in reverse. If the fill weight is fixed by the capsule or the tablet, the monohydrate delivers more zinc in that weight; if the zinc dose is fixed, the monohydrate needs less powder. Both are valid, but the change has to be written down.
What the water does in the formula
Water is the practical difference in a blend. A monohydrate adds about 10 g of water per 100 g of salt; the heptahydrate adds about 44 g. A moisture-sensitive active, a carbonate or a hygroscopic vitamin sees more than four times the water load from the heptahydrate, even though both are sold as dry powders.
The water also moves between the salt and its surroundings. The heptahydrate gives up surface water in a dry store and takes it back in a humid one; the monohydrate is less mobile but still hygroscopic. A change of hydrate can change flow, caking and water activity, so stability work belongs to the formula as well as to the salt.
Read the water lines carefully. On the monohydrate, ≤1.0% LOD is free moisture, not the 10.0% crystal water. On the heptahydrate, the 43–46% Karl Fischer figure is the crystal water itself. The numbers are not comparable, and a certificate that reports only LOD gives the total water of neither.
Fill weight and the capsule
Start from the label: 10 mg of zinc. Divide by the zinc fraction: 10 ÷ 0.364 = 27.5 mg of monohydrate, or 10 ÷ 0.227 = 44.0 mg of heptahydrate. At 15 mg the figures are 41.2 mg and 66.0 mg. The difference is capsule space and the excipient needed to reach a workable fill.
The error to avoid is a straight swap. Keep the 44.0 mg fill and switch to the monohydrate, and the capsule carries 44.0 × 0.364 = 16.0 mg of zinc where the label says 10 mg, about 60% high. Reverse it and 27.5 mg of heptahydrate carries 6.3 mg, about 37% low. The salt can pass release in both cases; the finished product is what misses.
Small doses bring a second issue: a 27.5 mg load inside a 500 mg capsule is a small share of the fill, so uniformity and carrier choice matter more than at 44.0 mg. A tablet made by direct compression also needs its weight and hardness targets reset.
What the label declares
The label carries elemental zinc, not the hydrate. EU labelling puts “zinc sulphate” in the ingredient list; the zinc mass and the percentage of the 10 mg reference intake sit in the nutrition declaration. US labelling puts “Zinc (as zinc sulfate)” in the Supplement Facts panel, with the elemental mass and the percentage of the 11 mg daily value. The hydrate need not appear on either label; the specification and the COA carry it.
So a 10 mg claim can be met by 27.5 mg of monohydrate or 44.0 mg of heptahydrate. Both labels are correct; the capsules differ. The hydrate is a specification detail, repeated on the certificate and in the change record; the consumer sees only the zinc figure.
The destination rules apply on top. EFSA sets a tolerable upper intake level of 25 mg zinc per day for adults; the US level is 40 mg. An authorised EU zinc claim has its own condition, usually that the food is a source of zinc at 15% of the reference value per portion. The reviewer checks the claim against the finished dose, which is elemental zinc.
What a switch requires
A change of hydrate is a change of material. Recalculate the fill with the batch zinc figure, not the theoretical one. Check blend flow, tablet weight and hardness, capsule fill and blend water, and repeat stability if the pack or storage humidity changes.
Revise the specification, the bill of materials and the change-control record, and reissue the artwork if the zinc mass moves. Retain samples of both hydrates so a disputed fill can be checked. A gram-for-gram swap is not neutral: it adds about 60% zinc one way and removes about 37% the other.
The monohydrate page has the catalog specification; the heptahydrate page has the other figures; the grades page puts this comparison in the context of the range; the COA page shows how zinc and water are reported; the methods library covers titration and water; the quality page covers release and change control.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation