06 Identity & adulteration

How we prove a zinc picolinate lot is the picolinate

Technical document 06 · Reviewed 2026-11-19 · Zinc Picolinate

On this page
  1. Identity in layers
  2. The 2:1 ratio and the mass balance
  3. What XRD sees, and what it misses
  4. Adulteration signals
  5. What to write into the specification
  6. Questions to put to the supplier

Four measurements have to agree before a zinc picolinate lot is identified: the IR spectrum of the complex, the HPLC assay, the complexometric zinc result and the mass balance between them. A zinc figure on its own fits several salts, and a ligand figure on its own fits added picolinic acid. The 2:1 ligand-to-zinc ratio is what forces the two figures to describe the same molecule.

In one line

Zinc picolinate is proved by agreement: the spectrum, the ligand assay, the zinc titration and the 2:1 ratio have to tell the same story.

Identity in layers

Each test answers a narrower question than the one before it. Appearance and solubility only establish that the powder could be the right material. IR establishes that the picolinate is coordinated to a metal. HPLC measures how much of the complex is present. The titration measures the metal, and the arithmetic between the two is the only step that tests whether ligand and metal belong together. XRD adds a check for a crystalline second phase.

Identity layers · what each test answers
LayerTestQuestion answeredTarget
Appearance, solubilityVisual; water dispersionCould this be the material?White to off-white; only slightly soluble
Complex identityIRIs the picolinate coordinated?Matches the reference
AssayHPLCHow much complex is present?98.0–102.0%
MetalComplexometric titrationHow much zinc is present?20.0–21.5%
Mass balanceCalculationDo ligand and metal agree?2.00 mol ligand per mol zinc
Second phaseXRDIs crystalline zinc oxide present?None above the detection limit

A disputed lot is worked in that order, because the calculation is free and it often shows which instrument is needed next. Repeating a test that has already passed adds precision, not evidence.

The 2:1 ratio and the mass balance

The molar arithmetic is fixed by the formula. Picolinate is 122.10 g/mol, zinc is 65.38 g/mol, and 2 × 122.10 + 65.38 = 309.58 g/mol, which is 21.12% zinc. If a laboratory reports the ligand as free picolinic acid at 123.11 g/mol, the moles are the same and the ratio is unchanged.

To check a lot, convert both results to moles and divide. A true complex returns 2.00. A ratio of 2.20 carries more ligand than the formula allows, which suggests added picolinic acid; 1.70 leaves metal in excess of the ligand, which suggests a second zinc source. Both numbers say more than a second assay would.

The basis has to match. A ligand result on the dried basis divided by a zinc result as-is produces a ratio that belongs to neither. And total ligand includes free ligand, so a free picolinic acid figure belongs beside the ratio rather than in a footnote.

A worked case: a 99.0% assay implies 20.9% zinc. A titration of 20.9% closes the balance. A titration of 24.0% means roughly one zinc in eight comes from elsewhere, and a titration of 18.0% means dilution or excess ligand. The arithmetic decides which test is worth ordering.

What XRD sees, and what it misses

Zinc oxide is the common second source, and it is crystalline, so XRD is the direct screen. The picolinate gives a distinct pattern, and zincite reflections stand out when oxide is present. The detection limit on the report is part of the evidence; a “none detected” without a limit is a statement about the instrument.

The method has limits of its own. Amorphous material and dissolved species produce no reflections, and a blend below the detection limit is invisible. That is why XRD sits beside IR and the mass balance rather than replacing them. A clean IR with a 24% zinc figure still describes a blend.

Adulteration signals

What a result pattern suggests, and how to confirm it
SignalLikely causeNext test
Zinc above 21.5%, assay near 100%Zinc oxide additionXRD and IR
Zinc near 21%, sulfate presentZinc sulfate heptahydrate, about 22.7% zincSulfate test or ion chromatography
Ligand high, zinc lowFree picolinic acidFree-acid HPLC
Assay and zinc low, moisture highDilution or water uptakeMoisture and mass balance
Zinc in range, IR mismatchA different zinc saltIR reference and HPLC

Zinc sulfate heptahydrate is the hardest case to see: 22.7% zinc sits close enough to the picolinate range that the titration alone will not catch it. A sulfate test or ion chromatography will, and the moisture result should sit well above the 1.0% ceiling if the heptahydrate is a large share. Zinc gluconate at 12.5–14.0% and zinc citrate at 31.0–32.5% are further away and easier to spot in the arithmetic.

What to write into the specification

  • “Zinc picolinate, CAS 17949-65-4, C12H8N2O4Zn; HPLC assay 98.0–102.0% with the basis stated.”
  • “Zinc 20.0–21.5% by complexometric titration, on the same basis as the assay.”
  • “IR and HPLC identity against reference materials.”
  • “Loss on drying ≤1.0%; no water of crystallisation in the formula.”
  • “No second zinc source; XRD screen with its detection limit on request.”
  • “Free picolinic acid reported where the ligand figure exceeds the balance.”

The clauses do the work a zinc range cannot: they define an article rather than a metal content.

Questions to put to the supplier

  1. Is this one complex or a blend? If a blend, which zinc sources are present and in what share?
  2. What are this lot's assay and zinc results, and on what basis was each reported?
  3. Does the IR report compare against a reference spectrum, and which bands were used?
  4. Has zinc oxide been screened by XRD, and what detection limit is quoted?
  5. Is free picolinic acid reported, and does the ligand close against the zinc?

Five answers of that kind form a specification. A single zinc percentage does not. The product hub carries the catalogue specification, and the COA page shows how the results are laid out. The picolinate versus bisglycinate page covers the ligand comparison; the XRD note explains what a detection limit means, and the FTIR note covers the coordination spectrum. The full method list is on the methods index, and the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation