Zinc picolinate grades: powder, granulation and the blend question
Zinc picolinate is a single complex — two picolinate ligands on one zinc — so the usual hydrate menu does not exist here. What the buyer can choose is the physical state of the powder and whether the drum holds that one complex or a mixture with a second zinc source. The zinc figure, the mesh and the label follow from those two choices.
Zinc picolinate has no hydrate ladder; the grade choice is the physical form of the powder and whether the drum holds one complex or a blend.
Why this product has fewer grades
Citrate has a dihydrate and an anhydrous salt; sulfate is normally bought as the heptahydrate. For both, the hydrate decides how much zinc sits in a gram before any other question is asked. Picolinate does not work that way. The complex is Zn(picolinate)2, the formula has no water of crystallisation, and the catalogue's 20.0–21.5% zinc sits around the 21.12% the formula predicts. Moisture is capped at 1.0% because the powder picks it up in handling, not because water is part of the crystal.
So a grade conversation about picolinate is short. It is about how the powder runs and what else is in the drum. “Zinc picolinate 99%” answers neither question: the number might be the assay, the zinc content, the through-sieve fraction, or a naming convention.
The presentations side by side
| Grade | Zinc figure | What it is | Fits | Watch |
|---|---|---|---|---|
| Standard powder, 40 mesh | 20.0–21.5% | One complex, milled and sieved | Capsules, tablets, dry blends | Sieve and moisture results for the lot |
| Granulated | Same as the base powder | Agglomerated for flow and density | Tablets, sachets, high-speed blends | Binder declared; assay re-run after granulation |
| Oxide blend | Above 21.5% | Picolinate plus zinc oxide | Formulas that need more zinc per gram | Two sources; both belong on the label |
| A different zinc salt | 12.5–14.0% gluconate; 31.0–32.5% citrate | Another article under a chelate description | Only where that salt is declared | New CAS, new name, new specification |
Row four is a warning rather than an option. Zinc gluconate and zinc citrate have their own CAS numbers and their own ingredient names, and neither is a grade of the picolinate. A drum sold as “zinc chelate” with no ligand named has not been specified at all.
Particle size, flow and moisture
Mesh is the first lever. The catalogue powder passes 40 mesh at ≥95%, and that single figure hides a distribution: a lot with many fines dusts, wets quickly and can segregate, while a coarse lot flows well and disperses slowly. Ask for the sieve result, not only the pass mark.
Granulation is the second lever. It binds the same particles into larger, denser agglomerates, which improves flow on a press or a sachet line. It also introduces a binder and a new mass, so the assay belongs on the granulated powder and the binder belongs in the declaration.
Moisture is the third. A 1.0% ceiling is tight, and a powder left open in a humid room can exceed it while the zinc figure still reads normally. Caking and slower flow are the visible signs; the moisture result on the lot is the evidence.
What changes in the finished product
Fill weight follows the zinc figure. At 21% zinc, a 15 mg claim needs about 71 mg of powder; at the low end of the range it needs 75 mg, and at the high end 70 mg. The difference looks small until the capsule is fixed and the excipients are counted. A capsule that holds 70 mg comfortably can be tight at 75 mg.
Tablets add compaction. A granulated grade usually runs better at high zinc loads, with fewer fines and less picking, but the lubricant and binder have to be compatible with the label and with the moisture limit.
Sticks and drinks are a different problem. The powder is only slightly soluble, so it disperses, and an opaque suspension is the realistic format. A clear beverage is not where this salt starts. Gummies and chews bring water activity and pH into play, and the taste of the zinc has to be worked into the flavour system.
What to put in the specification
- “Zinc picolinate, CAS 17949-65-4, C12H8N2O4Zn; zinc 20.0–21.5% by complexometric titration.”
- “HPLC assay 98.0–102.0%, with the basis named.”
- “IR and HPLC identification against reference materials.”
- “Loss on drying ≤1.0%; ≥95% through 40 mesh; bulk density as measured on the lot.”
- “One complex only: no zinc oxide or second zinc source; XRD screen and detection limit if the form is challenged.”
- “Granulated: binder named, assay repeated after granulation.”
A specification that stops at the zinc range has described a metal content. The clauses above turn it into something a laboratory can release against.
When not to change grade
When the label claim is elemental zinc and the capsule has room, the 40 mesh powder needs no upgrade. Granulation solves a flow problem; it does not improve a blend that already flows. A blend solves a zinc-density problem; it does not belong in a drum whose label names one source.
Sometimes the answer is a different salt rather than a different grade. Zinc bisglycinate dissolves, which is why it appears in clear drinks and stick packs; zinc citrate carries 31.0–32.5% zinc and fits a smaller capsule. Moving salt is a new article, and the label, fill weight and stability file move with it.
The product hub carries the catalogue specification. The comparison with the glycine chelate is on the picolinate versus bisglycinate page; the certificate fields are on the COA page; the powder's behaviour in a matrix is on the stability page.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation