Zinc oxide vs zinc bisglycinate: what the blend hides
Zinc oxide is about 80% zinc by mass; zinc bisglycinate monohydrate is about 27%. A blend of the two can land anywhere between those figures, including a number that looks like a stronger chelate grade. The zinc assay cannot tell the two sources apart, so the blend stays hidden unless the certificate reports the ligand and a crystal-form test.
At about 80% zinc, oxide can lift a 27% chelate to almost any figure, and the zinc assay will not say so.
Two numbers, two materials
Zinc oxide, ZnO, is about 80% zinc by mass. Zinc bisglycinate monohydrate is about 27%. The gap is chemical, not a matter of grade: an inorganic oxide on one side, an organic chelate on the other. The chelate carries a fixed 1:2 zinc–glycine ratio, and roughly three-quarters of its mass is ligand and water rather than the metal.
The arithmetic is the first check on a quotation. A powder whose zinc figure sits materially above the chelate's ceiling cannot be the single chelate. It is a blend, a different salt, or a material whose assay has been calculated on a different basis. A figure inside the chelate range does not prove the chelate either: a blend can be formulated to land inside the range. The number narrows the question; it does not answer it.
Why blends exist
Blending answers three pressures. Zinc oxide carries much more zinc per gram, so a blend raises the elemental figure and reduces the mass needed per dose. It is a dense powder, so it can improve flow in a light chelate blend. And it lets a supplier offer a range of zinc figures from one chelate stock. A formulator may choose a blend deliberately: a high-zinc, low-mass powder can be the right answer for a capsule with a tight fill weight.
The difficulty begins when an undeclared blend is sold under the chelate name, because the label then describes a material that is not in the drum. A declared blend with both sources on the label is a different product from an undeclared blend with one name on the certificate.
How a blend is detected
| Test | What it shows | Limit |
|---|---|---|
| Zinc assay | Total zinc | Cannot separate sources |
| Glycine assay | Total ligand | Includes free glycine |
| Zn : glycine ratio | Consistency with a 1:2 chelate | Calculated; needs both assays on one basis |
| XRD | Crystalline zinc oxide above the detection limit | Does not see amorphous or dissolved species |
| FTIR | Glycine coordination | Not a quantitative blend ratio |
Start with arithmetic, then go to the ligand. If the zinc figure is above the chelate ceiling, another zinc source is present. If the glycine figure is low relative to the zinc, part of the metal is not chelated. XRD then looks for crystalline zinc oxide, and FTIR for the coordination of glycine to zinc. A cloudy water dispersion is a hint, not proof; zinc oxide is practically insoluble in water, but a cloudy powder can have other causes. Evidence comes from the elemental result, the ligand result and a method that sees the solid state, taken together.
What the label can say
EU labelling requires the zinc source to be named as it appears in Annex II to Directive 2002/46/EC. Zinc bisglycinate and zinc oxide are separate entries. In a blend, both sources must appear in the ingredient list, ordered by weight. Naming only the chelate while oxide is present is a labelling defect before it is a quality defect.
In the US the Supplement Facts panel declares elemental zinc; the source sits in the ingredient list. If both are present, both should be named. A consumer reading only the zinc number cannot tell which form was used.
The same logic belongs in the purchase order. A purchase order for the chelate obliges the certificate to prove the chelate; an order for a blend obliges it to name the components and their proportions. An order that names only a zinc percentage has not specified a material.
What to write into the specification
- “Zinc bisglycinate monohydrate, 1:2 chelate; no added zinc oxide.”
- “Zinc 26.0–28.0%; glycine 59.5–64.5%; Zn : glycine 1.95–2.05; free glycine ≤1.0%.”
- “XRD: no crystalline zinc oxide detected, detection limit reported.”
- “FTIR coordination reported on request.”
- “If blended, declare each zinc source and its contribution; name the blender on the certificate.”
Ownership of the blend declaration should be written into the specification. When blending happens after chelation, the blender becomes the manufacturer of the blend and should issue the certificate; the chelate producer's COA no longer covers the drum.
Five questions for the supplier
- Is this a single chelate, or a blend? If blended, what is in it and at what proportion?
- Which zinc and glycine results belong to this lot, and on what basis were they reported?
- Does an XRD report cover crystalline zinc oxide, and what detection limit does it state?
- Is an FTIR spectrum available for glycine coordination?
- Which hydrate is declared, and is any other zinc source present?
Five direct answers amount to a specification; a single zinc percentage does not. The grade page places this question in the wider range; the identity page gives the full test sequence; the COA page shows where each figure sits on the certificate; the compliance page covers the label rules; the XRD note explains the detection limit; the product hub carries the specification.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation