02 Grade comparison

27%, 20% or a blend: choosing a zinc bisglycinate grade

Technical document 02 · Reviewed 2026-11-18 · Zinc Bisglycinate

On this page
  1. Why the grade is not the assay
  2. The grades side by side
  3. What changes in the drum
  4. What changes in the finished product
  5. When not to change grade
  6. What to put in the specification

Zinc bisglycinate is sold as a monohydrate at about 27% zinc, an anhydrous chelate with more zinc per gram, a spray-dried grade at about 20%, a blend with zinc oxide, and granulated or milled versions of the same powder. The grade changes the fill weight, the flow and what the label can say. The highest zinc figure is not automatically the right grade.

In one line

The dosage form and the label choose the grade; the zinc percentage on the first quotation does not.

Why the grade is not the assay

Three variables hide behind one grade name: the hydrate state, the physical presentation, and whether a second zinc source is in the drum. The zinc percentage reflects all three choices at once; it does not explain them. A 27% monohydrate and a 20% spray-dried powder can both be the same chelate at different presentations; a powder whose zinc figure sits above the chelate's ceiling is not the single chelate, whatever the label says.

The question that matters is not the zinc percentage but the molecule, its hydrate and the rest of the drum. That answer sets the label, the fill weight, the press behaviour and the taste.

The grades side by side

Zinc bisglycinate grades · what changes in the drum
GradeZinc figureWhat it isFitsWatch
Monohydrateabout 27%1:2 chelate with one water; reference gradeCapsules, tablets, sticksConfirm loss on drying and hydrate on COA
Anhydroushigher than monohydrate1:2 chelate without waterTight fill weights; dry blendsConfirm moisture pick-up and packing
Spray-driedabout 20%Spray-dried presentation of the chelateSticks, blends that need flowAsk what the 20% is measured against and what carries the powder
Zinc oxide blendabove the chelate ceilingChelate plus zinc oxideProjects that want a higher zinc figureNot a single chelate; label must name both sources
Granulatedsame as base gradeAgglomerated powderTablets, sachetsConfirm granulation aids and assay
Milledsame as base gradeFiner powder, 80 mesh on requestCapsules, suspensionsCaking, dust and segregation

What changes in the drum

The monohydrate is the reference grade. At about 27% zinc, 100 mg of powder carries about 27 mg of elemental zinc; a 20% grade carries about 20 mg, so the fill weight has to rise for the same dose. The arithmetic is simple, but it has to be redone deliberately. A formula built on 27% and switched to 20% without recalculating the fill weight will under-deliver the label claim.

The anhydrous chelate carries more zinc per gram because it has no water of crystallisation. It can suit a formula with a tight capsule fill, provided the certificate confirms the loss on drying and the packing protects the powder from moisture. The spray-dried grade changes particle structure and flow; ask what the 20% figure is measured against and what carries the powder, because both belong in the label.

Granulation and milling do not change the chemistry. They change flow, density, dust and dispersion. A granulated grade can run on a tablet press that a fine powder would choke; a milled grade can suspend in a drink where a coarse powder would settle. Either is valid if the specification names the process and any excipient.

What changes in the finished product

For capsules, the fill weight is the limit. A 27% grade fits more zinc into a small capsule than a 20% grade, which matters when the dose is high and the capsule size is fixed. Tablets add flow, density and compression: a granulated grade may help a blend that is too light, while a finer grade may need a different lubricant. Stick packs and drink mixes care about dispersion and taste more than the last decimal of the assay; a spray-dried grade can be easier to disperse, but the carrier has to be declared.

Gummies and chews are a matrix problem. pH, water activity and the sugar system decide how the chelate behaves, and the taste of the zinc becomes part of the product. Formulators often choose the chelate for capsules and tablets because it is less prone to the metallic taste and gastric irritation associated with some inorganic salts; that is a formulation observation, not a health claim.

The daily portion has to be checked against the destination market. Zinc has an EU upper level and labelling rules, and the US has its own Daily Value; the grade decision is also a dose decision.

When not to change grade

If the label claim is elemental zinc, the formula has room for the extra powder, and the certificate documents the form, the monohydrate is enough. The anhydrous grade earns its place only when fill weight or capsule size is the real constraint. Granulation does not improve a capsule blend that already flows, and a finer mesh does not help a tablet blend that needs density. Spray-drying is wasted on a dry blend that disperses without it.

Choose the grade for a problem the dosage form actually has. Switching grade is a revalidation: fill weight, flow, taste, stability and label all move, and the new certificate must repeat the new definitions.

What to put in the specification

  • “Zinc bisglycinate monohydrate, 1:2 chelate; zinc 26.0–28.0% by complexometric EDTA.”
  • “Glycine 59.5–64.5% by HPLC, basis stated; Zn : glycine 1.95–2.05.”
  • “Free glycine ≤1.0%; loss on drying ≤8.0%.”
  • “Particle size ≥95% through 40 mesh; bulk density 0.40–0.70 g/mL.”
  • “No added zinc oxide; XRD oxide screen reported with its detection limit.”

A line that reads only “zinc bisglycinate 27%” leaves both the presentation and the oxide question open. The table is useful only if the certificate repeats the same definitions; otherwise the buyer is comparing a name, not a material.

The parameters behind these figures are set out on the COA page. The blend route has its own page: oxide versus bisglycinate. Regulatory status is covered on the compliance page, and the full specification is on the zinc bisglycinate hub.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation