06 Identity & adulteration

How we prove a selenium glycinate lot is the chelate

Technical document 06 · Reviewed 2026-11-20 · Selenium Glycinate

On this page
  1. The identity layers
  2. The glycine ratio is a calculation, not a measurement
  3. What XRD can and cannot add
  4. The routes that produce a false positive
  5. Writing the identity into the specification
  6. Five questions to ask

A selenium glycinate lot is the chelate when four measurements agree: the documentation names the article and the carrier, total selenium by ICP-MS gives the element, glycine by HPLC with the free fraction gives the ligand, and speciation shows whether the two are bound together. The mass balance then has to add up. At 1.0–2.0% selenium most of the powder is carrier, so the glycine ratio only becomes meaningful when the carrier is declared and the free glycine is subtracted.

In one line

At one to two percent selenium the element figure is the easy part; identity is the glycine ratio and the speciation that show the selenium is bound to the ligand rather than blended beside it.

The identity layers

Identity layers · what each proves and what it misses
LayerEvidenceProvesMisses
DocumentName, carrier, presentation, specificationWhat the lot is calledEverything about the drum
ElementSelenium by ICP-MSHow much selenium is presentWhether it is bound or inorganic
LigandGlycine by HPLC; free glycineThat the ligand is present and in what amountWhether the ligand is bound to selenium
SpeciationIC-ICP-MS or HPLC-ICP-MS after a defined extractionThe fraction that is inorganicThe exact structure of the bound species
Mass balanceSelenium, glycine, loss on drying, carrierWhether the numbers add upWhich carrier fraction is which

The layers are independent by design. A blend of sodium selenite and glycine passes the document, element and ligand layers; only speciation separates it from the chelate. A chelate with free glycine added passes the document and element layers; the free-glycine figure catches it.

The glycine ratio is a calculation, not a measurement

The catalog line reads “glycine (HPLC): chelate ratio conform”, and that phrase hides two operations. HPLC measures a glycine figure; the ratio is calculated from it. A certificate that reports only “conforms” has not shown the figure, the basis or the arithmetic, and the reader cannot check any of them.

The arithmetic is simple once the basis is fixed. Selenium is 78.97 g/mol and glycine is 75.07 g/mol. If the complex were 1:1, each gram of selenium would carry about 0.95 g of glycine; at 1:2 it would carry about 1.90 g. For a 1.5% selenium material, a 1:1 complex accounts for about 1.4% glycine and a 1:2 complex for about 2.9%. A total glycine figure far above that range is not evidence of more chelate; it is evidence of free glycine or a glycine-rich carrier.

Total glycine and free glycine have to be reported separately. Subtract the free fraction, convert the bound glycine to moles, divide by the moles of selenium, and report the result with the calculation. If the carrier itself contains glycine, the total figure is uninformative without a blank run on the carrier alone. That is why the carrier belongs in the specification, not in a footnote.

What XRD can and cannot add

X-ray diffraction is a solid-state test, and at this selenium load the diffractogram is dominated by the carrier. An amorphous carrier gives a broad halo; a crystalline carrier gives its own pattern. XRD can show a carrier change, a crystalline phase and, above its detection limit, crystalline free glycine in a blend. It cannot show that selenium is coordinated to glycine, because the selenium is a minor component and the pattern belongs to the bulk.

Infrared spectroscopy is the better ligand-side support: the carboxylate bands of a coordinated glycine shift against those of the free amino acid. The same matrix problem applies, and a carrier with strong bands can swamp the region of interest. Use FTIR as supporting evidence, not as the identity test. For XRD, ask for the reference pattern, the detection limit and the sample preparation; “XRD conforms” without them has added little.

The routes that produce a false positive

Adulteration routes and the test that catches each
RouteWhy it appearsCaught by
Selenite or selenate blended with glycineA readily available inorganic source that lifts the element figureSpeciation; inorganic selenium fraction
Selenomethionine diluted and renamedA high-selenium organic source cut to 1–2%Speciation; the selenomethionine peak
Selenium yeast blended inAn organic matrix with its own seleniumProtein and yeast markers; speciation
Free glycine addedLifts the glycine figure without adding chelateFree glycine; a blank on the carrier
Elemental seleniumA red or grey tint; an insoluble fractionAppearance; a hazy solution; speciation
Carrier substitutionChanges selenium per gram and the labelCarrier declaration; loss on drying; mass balance

The strongest single screen is speciation, because it is the only test that separates bound selenium from the inorganic salt. The second is the free-glycine figure with a carrier blank. A certificate that reports total selenium and total glycine but neither speciation nor free glycine has left the most likely substitutions untested.

Writing the identity into the specification

  • “Selenium glycinate; carrier and presentation declared.”
  • “Selenium 1.0–2.0% by ICP-MS, with the basis, the isotope and the digestion stated.”
  • “Glycine by HPLC, total and free, with the chelate ratio and the calculation reported.”
  • “Inorganic selenium fraction by speciation, with the extraction and the limit of quantification.”
  • “Loss on drying ≤5.0%; particle size ≥95% through 80 mesh.”
  • “No added selenium source other than the declared one; change control for carrier and source.”

Five questions to ask

  1. What is the glycine figure, total and free, and what ratio does it calculate to?
  2. What carrier is present, and was a blank run on that carrier?
  3. Has speciation been run, and what fraction of the selenium is inorganic?
  4. Which selenium source and ligand were used, and on what basis is the selenium result reported?
  5. Does the XRD or FTIR report name a reference and a detection limit?

Five direct answers amount to an identity file; one selenium percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grade page covers the carrier and the presentation; the comparison with selenomethionine shows how the identity tests differ; the methods library describes the separation; the quality page covers the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation