02 Grade comparison

Selenium glycinate grades: selenium load, carrier and mesh

Technical document 02 · Reviewed 2026-11-20 · Selenium Glycinate

On this page
  1. Why the load is low and the window is wide
  2. Presentations and the sources beside them
  3. Powder, solution and handling
  4. The dose arithmetic and the label
  5. What to write into the specification
  6. When this grade is the wrong choice

Selenium glycinate is supplied as a white to off-white powder at 1.0–2.0% selenium, ≥95% through 80 mesh, with granulation on request. The grade decision is the selenium load, the carrier and the mesh; the load is what changes the weigh-up, the blend uniformity and the number on the label.

In one line

The grade is the selenium load and the carrier: at 1.0–2.0% selenium the powder is mostly ligand matrix and carrier, and the label follows the declaration.

Why the load is low and the window is wide

The commercial material is a low-load chelate, not a single crystalline molecule with a formula that fixes the selenium percentage. The selenium figure depends on how much of the complex was formed and how much carrier was used to make a powder that flows, weighs and disperses. That is why the catalog window is 1.0–2.0%: two conforming lots can differ by a factor of two in selenium per gram.

The window is a specification, not a quality grade. A lot at 1.0% is not a lower grade than a lot at 2.0%; it is a different load of the same chemistry, and the formula has to be built on the value in the certificate. A buyer who takes 1.5% as “the” figure and ignores the lot value will be wrong at both edges.

Presentations and the sources beside them

Selenium glycinate presentations
PresentationSeleniumParticle sizeTypical useWhat changes
Standard powder1.0–2.0%≥95% through 80 meshCapsules, tablets, powder blendsThe catalog presentation
Granulated1.0–2.0%On requestFlow and dust controlParticle profile and bulk behaviour

Granulation is a physical change: the chemistry and the selenium figure stay, while the particle profile and the flow move. It is not a drop-in for the standard powder without a specification revision, and the sieve result on the certificate belongs to the granulated article, not to the powder.

The source decision sits beside the presentation decision. L-Selenomethionine is a single amino acid at 39.0–41.0% selenium, selenium yeast is a matrix at 1,800–2,200 mg/kg, and sodium selenite is an inorganic salt at 44.0–46.0%. Those are different ingredients, not grades of this one; the chelate comparison is worked through on the selenium glycinate and selenomethionine page.

Powder, solution and handling

The powder is white to off-white and free-flowing at 80 mesh. It dissolves in water to a clear solution, which is a useful observation but not a release test: a haze can mean an insoluble carrier, and a pink or grey tint can mean elemental selenium rather than a shade of white. The material is hygroscopic, so the 5.0% loss-on-drying limit is a release gate and an in-use warning at the same time.

Granulation improves flow and reduces dust, which matters on a capsule line and in a low-dose blend. It does not change the selenium figure, but it changes the bulk behaviour and may change the uniformity result. The 1.0–2.0% window is already a low selenium per gram, so the powder is normally used as a premix rather than diluted further.

The dose arithmetic and the label

The selenium figure connects the label to the weigh-out. At 1.0% selenium, a 55 µg dose is 5.5 mg of material; at 1.5% it is 3.67 mg; at 2.0% it is 2.75 mg. The same arithmetic at 200 µg gives 20 mg, 13.3 mg and 10 mg. These are small masses, which is why the material is usually handled as a premix rather than weighed into a capsule blend directly.

One check is worth doing before any trial: a 500 mg capsule filled with the powder at 1.5% selenium would carry 7.5 mg of selenium, about 29 times the EFSA tolerable upper intake level of 255 µg/day for adults. The figure is a hazard reference, not a permitted maximum, and the arithmetic is the point: this is a premix ingredient, not a capsule fill on its own.

The label declares selenium in micrograms against the 55 µg reference intake, and the ingredient list names the source. The carrier is an ingredient, and the selenium figure on the label is calculated from the article as supplied. The weigh-up uses the lot value, and the overage, if any, belongs to the brand's formulation and stability work.

What to write into the specification

  • “Selenium glycinate, white to off-white powder; carrier and presentation declared.”
  • “Selenium 1.0–2.0% by ICP-MS, with the basis, the isotope and the digestion stated.”
  • “Glycine by HPLC with the free fraction; the chelate ratio and its calculation reported.”
  • “Loss on drying ≤5.0%; particle size ≥95% through 80 mesh.”
  • “Heavy metals and microbiology as listed; speciation on request.”
  • “The presentation — powder or granulated — and the pack named.”

When this grade is the wrong choice

If the label needs a single defined molecule, a specific rotation and a named entry on the EU permitted-forms list, the amino acid is the better fit: L-selenomethionine is listed and this chelate is not, as of this review. If the formula needs a higher selenium density to keep the premix mass down, the same applies. If the market file already names selenium yeast or sodium selenite, changing source is a relabelling project, not a grade change.

The chelate is the right choice when the label and the market route are built around it, when a water-soluble organic selenium source is wanted, and when the carrier and the presentation are declared. The catalog specification is on the product hub; the certificate lines are on the COA page; the market question is on the compliance page; the identity tests are on the identity page; the amino acid's specification is on the L-selenomethionine page; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation