What the COA for potassium citrate monohydrate actually contains
Every lot of potassium citrate monohydrate ships with a certificate reporting appearance, identification, assay by titration, elemental potassium, water by Karl Fischer, pH, heavy metals, microbiology and particle size. The assay measures the citrate salt; the potassium and water lines decide whether that salt is the monohydrate. Each line needs a method and a release limit beside the result, because a certificate of conclusions cannot be audited.
The assay says how much citrate salt is present, the potassium figure says how much of the element it carries, and the water says which hydrate was weighed; the three lines only mean something together.
The certificate as a test report
A release certificate is written against a specification, so each row has three parts: the parameter, the method that produced the number, and the limit the lot was released against. A result without a method cannot be repeated by a second laboratory; a limit without a result is a promise rather than a measurement.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White crystalline powder |
| Identification | Infrared spectrum and citrate reaction | Conforms to reference |
| Assay (citrate) | Perchloric acid titration | 99.0–100.5% |
| Potassium (K) | Flame photometry or ICP-OES | 35.0–37.0% |
| Water | Karl Fischer | 5.0–6.5% |
| pH (5% solution) | Potentiometry | Typically 7.0–9.0; range agreed |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
The identification row is a yes-or-no gate and should name the reference; the assay and potassium rows are numbers that answer different questions.
The assay basis, the potassium figure and the water
The assay is an acid–base titration of the citrate, quoted at 99.0–100.5%. The certificate has to print the basis in the same row: on the dried basis the crystal water is excluded from the denominator; as-is it is included. The same powder reads higher on the dried basis, and the gap is roughly the water figure, so two certificates must be converted to one basis before they are compared.
The molar arithmetic gives the check. Potassium citrate monohydrate is C6H5K3O7·H2O, molar mass 324.41. Three potassium atoms contribute 117.29, or 36.16% of the molecule; one water molecule contributes 18.02, or 5.55%. The catalogue brackets both: K 35.0–37.0% and water 5.0–6.5%. An anhydrous lot would sit near 38.3% K with water below 1%, and that is a different grade, not a better one.
The potassium line is elemental. Flame photometry and ICP-OES both measure the metal after the sample is dissolved, and neither one sees the citrate. That is why the potassium figure cannot replace the assay, and why the assay cannot prove the hydrate.
Water by Karl Fischer measures total water, including the water built into the crystal. Loss on drying at 180 °C drives off the same water, so the two methods can agree; Karl Fischer is the clearer statement because it does not depend on how the sample was heated. The pH line is a process signal: a 5% solution is alkaline, typically 7.0–9.0, and it moves with residual acid or alkali.
Release limit versus batch result
The release limit is the acceptance boundary; the batch result is what the laboratory measured. Both belong on the page, in separate columns, with the method beside them. A result column filled with the specification range is not a result.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | 99.0–100.5%, with basis | A measured percentage and the basis |
| Potassium | 35.0–37.0% | A measured percentage and the method |
| Water | 5.0–6.5% | A measured percentage by Karl Fischer |
| Heavy metals | Per element | One figure per element, in mg/kg |
| Microbiology | Counts and absence | The count and the absence statement for the lot |
“Conforms” is acceptable for identification and for the absence tests, provided the reference and the method are named. It is not acceptable for assay, potassium or water, where a number is the evidence. A certificate that reports a single “heavy metals” total has hidden the element that matters.
What moves between batches
The salt is made by neutralising citric acid with a potassium source, then crystallising and drying it. Potassium and water move together with the drying step: a lot dried too far loses crystal water and reads high in potassium with low water, while a wet lot reads low in potassium with high water. Both can sit inside a wide specification and still behave differently at the fill line.
The assay follows the purity of the crystallised salt and the amount of mother liquor left in it. The pH follows the same washing step and the ratio of acid to alkali. Particle size follows the mill and the sieve, and it can change without any change in the chemistry.
Colour is the least quantitative line. A white powder can take a grey or yellow tint from iron pickup in the dryer or a longer hold in the centrifuge while assay and potassium pass. A tint is a reason to read the batch record, not to reject on appearance alone.
Chloride is not on the catalogue sheet, but a potassium raw material can carry it; where potassium chloride is the concern, ask for chloride by ion chromatography on the same lot. The identity page shows where that result fits.
When to order an outside test
Order an independent test for a new source, a first regulated-market shipment, a label that names the monohydrate, or a dispute. The useful panel is not a full repeat of the certificate: infrared identity and a citrate reaction, potassium by ICP-OES, water by Karl Fischer, chloride by ion chromatography, ICP-MS and a microbiology count.
Add X-ray diffraction if the solid form is disputed: the monohydrate and the anhydrous salt have different patterns, and potassium chloride has a third. Ask the laboratory to report its detection limit for each screen; a “not detected” line without a limit says more about the method than about the sample.
Keep the chain of custody. The sample tested should be the retained sample, and the report should name the lot. When a result is contested, send the retained sample, the supplier's certificate and the specification, and ask for the tests that separate the forms rather than a repeat of the same assay.
What to compare between suppliers
Put six lines side by side: the salt and its hydrate, the assay range and basis, potassium and water, pH, particle size and bulk density, and the contaminant panel. Two quotations that agree on assay but differ on hydrate or basis are not describing the same powder.
The second layer is traceability: the certificate lot number, the pack label and the retained sample should carry one identifier. The catalogue line sits on the potassium citrate product page; the hydrate choice is on the grade page; the tests that separate the salt from a blend are on the identity page; the potassium method is described in the ICP-OES note; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation