06 Identity & adulteration

How we prove a lot is potassium citrate monohydrate

Technical document 06 · Reviewed 2026-11-19 · Potassium Citrate

On this page
  1. The four identity layers
  2. The potassium ratio: proving the element
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A lot is potassium citrate monohydrate when four lines agree: the document names the salt and its hydrate, the infrared spectrum and a citrate reaction match the reference, the potassium result sits near 36.2%, and the water result sits near 5.5%. The assay alone cannot separate the monohydrate from the anhydrous salt, from a blend with potassium chloride, or from a dilution.

In one line

Identity is four agreeing measurements: the document names the hydrate, the infrared spectrum and the citrate reaction name the salt, the potassium figure fits 36.2%, and the water closes the mass balance.

The four identity layers

A certificate can name the right material and still fail to prove it. The four layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of potassium citrate identity
LayerQuestionTestWhat it proves
DocumentAre the salt and hydrate named?Name, CAS number, formulaPaperwork only
SpectrumIs the solid the citrate salt?Infrared spectrum and citrate reactionThe salt, not the hydrate
ElementIs the potassium figure right?Potassium by ICP-OES or flame photometryThe element, not the anion
Mass balanceIs it the monohydrate, and is it diluted?Water by Karl Fischer; assayThe hydrate and consistency

The potassium ratio: proving the element

The monohydrate is 36.16% potassium by mass: three potassium atoms at 39.10 against a molar mass of 324.41. The anhydrous salt is 38.28% because the same three atoms sit on a lighter molecule, and potassium chloride is 52.45% because it carries one potassium per 74.55 g. A potassium result near 36% is consistent with the monohydrate; 38% points to the anhydrous grade, 52% to the chloride, and a low figure to a sodium salt or a dilution.

Potassium by ICP-OES is the direct check. The method dissolves the salt and measures the element; it does not see the citrate. Pair it with water: the monohydrate carries 5.0–6.5%, the anhydrous salt below 1%, and a wet lot above 6.5%. The pair is stronger than either line alone.

A chloride test is the third check. Potassium chloride is the most likely potassium salt to appear in a citrate lot, because it is a common potassium source and it raises the potassium figure. Silver nitrate gives a white precipitate with chloride, and ion chromatography gives a number. The catalogue does not include chloride, so ask for it when the source is new or the potassium figure is higher than the hydrate allows.

The citrate side needs its own evidence. The infrared spectrum of a citrate salt carries carboxylate bands near 1600 and 1400 cm−1, and a citrate reaction with calcium ions gives a characteristic precipitate. Either test alone is weaker than the pair, and both are weaker than the pair plus the potassium and water figures.

X-ray diffraction: the solid-state check

X-ray diffraction answers the solid-state question. The monohydrate and the anhydrous salt have different powder patterns, so a lot sold as the monohydrate but showing the anhydrous pattern has been mislabelled or over-dried. Potassium chloride has a cubic pattern that is easy to recognise, and sodium citrate has its own.

XRD is not a routine release test and it is not a purity assay. It sees crystalline phases above its detection limit and misses an amorphous dilution. Ask for the reference pattern and the detection limit before reading a “match” statement; a conformity with no pattern adds little.

What adulteration looks like

Common potassium citrate substitutions and the signals
AdulterantWhat it doesSignalTest
Potassium chlorideRaises potassium; no citrateK high; chloride presentChloride by IC, infrared, XRD
Sodium citrateLowers potassium; adds sodiumK low; sodium highICP-OES for K and Na
Anhydrous citrateNo crystal water; K highWater below 5.0%Karl Fischer, XRD
Citric acidLowers pH; dilutes the saltpH low; K lowpH, titration, infrared
WaterRaises water; lowers the as-is assayWater above 6.5%Karl Fischer
Sugar or maltodextrinLowers assay and potassiumK low; infrared differsAssay, infrared, optical rotation

Colour is the weakest signal. A white powder can be tinted by iron pickup during drying, and a pure lot can be slightly off-white; the tint alone says nothing about substitution. The stronger signals are the potassium figure, the water figure, the chloride result and the infrared spectrum.

How to write the identity into the specification

  • “Potassium citrate monohydrate, C6H5K3O7·H2O, CAS 6100-05-6.”
  • “Assay 99.0–100.5% by titration; state the basis.”
  • “Potassium 35.0–37.0% by ICP-OES; water 5.0–6.5% by Karl Fischer.”
  • “Identification by infrared spectrum and citrate reaction, against a named reference.”
  • “Chloride by ion chromatography, where the source or the potassium figure calls for it.”
  • “No added potassium chloride, sodium citrate or citric acid.”

Five questions for the supplier

  1. Which hydrate is this lot, and which CAS number is on the certificate?
  2. Can you provide the infrared spectrum and the citrate identity result, not only the assay percentage?
  3. What are the potassium and water results for this lot, and which methods produced them?
  4. What is the chloride result, and was it measured on the same sample?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single assay percentage does not. The product hub carries the catalogue specification; the COA page shows where each figure sits on the certificate; the grade page compares the hydrates; the chloride comparison covers the salt choice; the XRD method note explains the solid-state test.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation