02 Grade comparison

Potassium citrate monohydrate: choosing a grade and a mesh

Technical document 02 · Reviewed 2026-11-19 · Potassium Citrate

On this page
  1. The hydrate is part of the identity
  2. The grades side by side
  3. Solubility, pH and handling
  4. What changes in the finished product
  5. How to write the specification
  6. When not to switch

The catalogue grade is potassium citrate monohydrate, a 40 mesh powder carrying 35.0–37.0% potassium and 5.0–6.5% water. An anhydrous grade exists, and granulated or finer-milled variants are quoted on request; the hydrate and the particle size are separate specification decisions. The monohydrate is not a diluted anhydrous salt, because the water is built into the crystal.

In one line

Grade means the hydrate and the particle size: the monohydrate carries 5.5% crystal water and 36.2% potassium, the anhydrous salt 38.3%, and the mesh decides how the powder flows.

The hydrate is part of the identity

Water of crystallisation is part of the lattice, not surface moisture that a dryer can remove at will. Potassium citrate monohydrate is C6H5K3O7·H2O at 324.41 g/mol; the anhydrous salt is the same formula without the water at 306.40. The monohydrate is the commercial grade because the hydrate is defined, it dissolves freely, and it is less eager to take up water than the anhydrous form.

A purchase order that says “potassium citrate” has named a family, not a drum. The hydrate changes the potassium per gram, the mass per serving and the water figure on the certificate. The particle size is the second decision: a 40 mesh powder, a granulation and an 80 mesh mill are process variants of the same salt, but they flow, dust and fill differently.

The grades side by side

Potassium citrate grades · what changes between them
GradeWaterPotassiumTypical useWatch
Monohydrate, 40 mesh5.0–6.5%35.0–37.0%Capsules, tablets, sticksHygroscopic; caking if opened
AnhydrousBelow 1%About 38.3%Fill-limited dry formulasMore hygroscopic; different solid form
Granulated monohydrateAs the monohydrateAs the monohydrateTablets, sachetsFlow aids must be declared
Fine mill, 80 meshAs the monohydrateAs the monohydrateSuspensions, small capsulesDust and segregation

The anhydrous grade is not a concentrate in the marketing sense; it is the same salt without the crystal water. Its potassium is higher per gram, its water is lower, and its powder is more hygroscopic.

Solubility, pH and handling

Potassium citrate is freely soluble: about 140 g dissolves in 100 mL of water at room temperature, and a 5% solution is alkaline, typically pH 7.0–9.0. The salt is hygroscopic and can cake or deliquesce in humid air, so the pack and the store matter as much as the mesh.

Bulk density and flow are lot-specific, and the number that matters is the one on the certificate for the lot being bought. A granulated grade is chosen for flow and low dust, not for a higher potassium figure; granulation aids, if used, have to be declared. A fine mill dissolves faster but can dust and segregate in a blend.

The crystal water is not a coating. It is 5.5% of the mass, and it is the reason the monohydrate and the anhydrous salt need separate specifications, separate fill weights and, strictly, separate labels.

What changes in the finished product

The potassium figure drives the fill. At 36.16% potassium, 500 mg of elemental potassium needs 1,383 mg of the monohydrate; 99 mg needs 274 mg. The anhydrous salt at 38.28% needs 1,306 mg and 259 mg for the same doses. A 500 mg capsule holds about 181 mg of potassium from the monohydrate, so a high-potassium claim and a small capsule are not compatible.

In a stick pack or a drink mix, the monohydrate is the practical grade: it dissolves freely and the citrate note is part of the taste. In a tablet, the granulated grade flows and compresses; in a capsule, the 40 mesh powder is the default. The water in the monohydrate is not a filler and should not be treated as one; it is part of the ingredient identity and the fill arithmetic.

The label follows the hydrate. In the European Union the ingredient list names the potassium source in the form the destination requires, and the nutrition declaration reports elemental potassium in milligrams and as a share of the reference intake. A change from monohydrate to anhydrous at a fixed powder weight moves the declared potassium by about 6%, which is a new label and a new fill trial, not a note in the batch file.

How to write the specification

  • “Potassium citrate monohydrate, C6H5K3O7·H2O, CAS 6100-05-6.”
  • “Assay 99.0–100.5% by titration; state the basis.”
  • “Potassium 35.0–37.0%; water 5.0–6.5% by Karl Fischer.”
  • “pH of a 5% solution typically 7.0–9.0; ≥95% through 40 mesh.”
  • “No added potassium chloride or sodium citrate.”

For the anhydrous grade, replace the hydrate name, the water limit and the potassium range with that grade's own figures. A specification copied from the monohydrate and applied to the anhydrous salt will fail every lot, and the supplier will be right.

When not to switch

Do not switch hydrate or mesh without a change control. The label, the fill weight, the stability file and the approved specification all belong to the grade that was qualified; a new hydrate is a new material even when the assay is identical.

Do not choose the anhydrous grade only because the potassium figure looks higher. The gain is about 6% more potassium per gram, and it comes with a more hygroscopic powder and a different solid form; if the capsule has room and the label is already set, the switch buys little.

The product hub carries the catalogue specification; the chloride comparison takes the salt choice further; the potassium gluconate page shows how a lower potassium figure changes the fill; the magnesium citrate page applies the same citrate arithmetic to a divalent metal; the COA page shows where the hydrate is declared on the certificate.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation