How we prove a magnesium bisglycinate lot is the chelate, not a blend
Identity for magnesium bisglycinate is not a single test. It is a set of four answers: the chemical form, the ligand ratio, the crystal form and the absence of undeclared material. A magnesium assay answers only the first part of the first question, and a certificate that stops there cannot distinguish a chelate from a blend.
Identity here is the form and the ratio: the same magnesium number can come from a chelate, a blend or a hydrate.
The four layers
The first layer is the chemical form: a 1:2 magnesium–glycine chelate, not magnesium oxide, carbonate or citrate. The second is the ligand ratio: one magnesium per two glycine molecules, measured on the same lot. The third is the crystal form and hydrate state, which decide how much elemental magnesium the powder can carry. The fourth is the absence of undeclared material: a carrier, a second magnesium source or a residual solvent that the certificate does not mention.
Each layer needs its own method. A single assay cannot cover all four, and a supplier who offers only the magnesium figure has answered one quarter of the question.
The ratio is the most economical check
The anhydrous chelate is 13.9% magnesium and 86.1% glycine by mass. On a lot that is the pure chelate, the two assays should produce a molar ratio close to 1:2. If the magnesium is high and the glycine is low, part of the magnesium is coming from another source. If the glycine is high and the magnesium is low, the material may contain added glycine or a carrier.
The ratio is calculated, not measured directly. Its uncertainty is the sum of the two assay uncertainties, so the specification should give a range rather than a single figure. A range of 1.95–2.05 mol glycine per mol magnesium is tight enough to catch a blend and wide enough to allow normal analytical variation.
Crystallography and spectroscopy
| Test | Proves | Does not prove |
|---|---|---|
| Complexometric EDTA titration | Total magnesium | Which source the magnesium came from |
| HPLC for glycine | Total glycine | Whether the glycine is bound or free |
| Calculated Mg : glycine ratio | Consistency with a 1:2 chelate | Absence of a second magnesium source by itself |
| X-ray diffraction | Crystalline magnesium oxide, if present above the detection limit | Amorphous or dissolved species |
| FTIR | Coordination of glycine to magnesium | Quantitative blend proportions |
| Loss on drying / TGA | Water content and hydrate behaviour | Which hydrate if the sample is mixed |
X-ray diffraction is the most direct test for crystalline magnesium oxide. The detection limit depends on the instrument and the sample preparation, so the report should state it. A “not detected” result is only meaningful with that limit attached. FTIR adds the coordination evidence: a physical mixture of oxide and chelate does not show the same metal–ligand bands as a reacted chelate.
The adulteration routes
The first route is a blend with magnesium oxide. It raises the elemental magnesium, lowers the cost per kilogram of magnesium and can improve flow. The magnesium assay passes; the ligand ratio moves. The second route is a carbonate or hydroxide source, which also raises the magnesium and can leave a different pH and solubility profile. The third is added glycine: a blend can be pushed toward the expected glycine figure without adding chelate. The fourth is a hydrate substitution: the powder is the same chemical entity but carries less magnesium per kilogram than the label implies.
Each route has a different signature. The blend moves the ratio and may show oxide by XRD. Added glycine raises free glycine without raising bound glycine. Hydrate substitution shows up in loss on drying and in the elemental assay together. This is why the specification needs all three figures, not only the magnesium.
What to write into the specification
- “Magnesium bisglycinate, 1:2 chelate; no added magnesium oxide.”
- “Magnesium 13.5–14.2%; glycine 84.0–88.0%; Mg : glycine 1.95–2.05.”
- “Free glycine ≤1.0%.”
- “Loss on drying ≤2.0%; hydrate state stated on the certificate.”
- “XRD: no crystalline magnesium oxide detected; detection limit reported.”
Questions to put to a supplier
- What is the glycine figure on this lot, and how was it measured?
- What is the calculated Mg : glycine ratio?
- Is there an XRD report, and what is its detection limit?
- Is the hydrate state named on the certificate?
- Does the lot contain any magnesium source other than the chelate?
The COA page shows where these figures sit on the certificate; the grade page explains the hydrate arithmetic; the oxide versus bisglycinate page covers the blend route in detail.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation